| Age | Commit message (Collapse) | Author |
|---|
|
Wei Fang says:
====================
net: fec: fix some issues of ndo_xdp_xmit()
We encountered some issues when testing the ndo_xdp_xmit() interface
of the fec driver on i.MX8MP and i.MX93 platforms. These issues are
easy to reproduce, and the specific reproduction steps are as follows.
step1: The ethernet port of a board (board A) is connected to the EQOS
port of i.MX8MP/i.MX93, and the FEC port of i.MX8MP/i.MX93 is connected
to another ethernet port, such as a switch port.
step2: Board A uses the pktgen_sample03_burst_single_flow.sh to generate
and send packets to i.MX8MP/i.MX93. The command is shown below.
./pktgen_sample03_burst_single_flow.sh -i eth0 -d 192.168.6.8 -m \
56:bf:0d:68:b0:9e -s 1500
step3: i.MX8MP/i.MX93 use the xdp_redirect bfp program to redirect the
XDP frames from EQOS port to FEC port. The command is shown below.
./xdp_redirect eth1 eth0
After a few moments, the warning or error logs will be printed in the
console, for more details, please refer to the commit message of each
patch.
====================
Link: https://lore.kernel.org/r/20230706081012.2278063-1-wei.fang@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In the case of heavy XDP traffic to be transmitted, the console
will print the error log continuously if there are lack of enough
BDs to accommodate the frames. The log looks like below.
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
Not only will this log be replicated and redundant, it will also
degrade XDP performance. So we use netdev_err_once() instead of
netdev_err() now.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.
After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.
This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.
[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec
Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When a XDP program is installed or uninstalled, fec_restart() will
be invoked to reset MAC and buffer descriptor rings. It's reasonable
not to transmit any packet during the process of reset. However, the
NETDEV_XDP_ACT_NDO_XMIT bit of xdp_features is enabled by default,
that is to say, it's possible that the fec_enet_xdp_xmit() will be
invoked even if the process of reset is not finished. In this case,
the redirected XDP frames might be dropped and available transmit BDs
may be incorrectly deemed insufficient. So this patch disable the
NETDEV_XDP_ACT_NDO_XMIT feature by default and dynamically configure
this feature when the bpf program is installed or uninstalled.
Fixes: e4ac7cc6e5a4 ("net: fec: turn on XDP features")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Boris needs 6.5-rc1 in drm-misc-fixes to prevent a conflict.
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
In order to generate the prologue and epilogue, the BPF JIT needs to
know which registers that are clobbered. Therefore, the during
pre-final passes, the prologue is generated after the body of the
program body-prologue-epilogue. Then, in the final pass, a proper
prologue-body-epilogue JITted image is generated.
This scheme has worked most of the time. However, for some large
programs with many jumps, e.g. the test_kmod.sh BPF selftest with
hardening enabled (blinding constants), this has shown to be
incorrect. For the final pass, when the proper prologue-body-epilogue
is generated, the image has not converged. This will lead to that the
final image will have incorrect jump offsets. The following is an
excerpt from an incorrect image:
| ...
| 3b8: 00c50663 beq a0,a2,3c4 <.text+0x3c4>
| 3bc: 0020e317 auipc t1,0x20e
| 3c0: 49630067 jalr zero,1174(t1) # 20e852 <.text+0x20e852>
| ...
| 20e84c: 8796 c.mv a5,t0
| 20e84e: 6422 c.ldsp s0,8(sp) # Epilogue start
| 20e850: 6141 c.addi16sp sp,16
| 20e852: 853e c.mv a0,a5 # Incorrect jump target
| 20e854: 8082 c.jr ra
The image has shrunk, and the epilogue offset is incorrect in the
final pass.
Correct the problem by always generating proper prologue-body-epilogue
outputs, which means that the first pass will only generate the body
to track what registers that are touched.
Fixes: 2353ecc6f91f ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230710074131.19596-1-bjorn@kernel.org
|
|
Unaligned exception handler is needed in configurations with hardware
support for unaligned access when the load/store exception handler is
enabled because such configurations would still raise an exception on
unaligned access through the instruction bus.
Fixes: f29cf77609cc ("xtensa: add load/store exception handler")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
split_if_spec expects a NULL-pointer as an end marker for the argument
list, but tuntap_probe never supplied that terminating NULL. As a result
incorrectly formatted interface specification string may cause a crash
because of the random memory access. Fix that by adding NULL terminator
to the split_if_spec argument list.
Cc: stable@vger.kernel.org
Fixes: 7282bee78798 ("[PATCH] xtensa: Architecture support for Tensilica Xtensa Part 8")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
iss_net_configure explicitly frees etherdev in all error return paths
except one where register_netdevice fails. In that remaining error
return path the etherdev is freed by the iss_net_pdev_release callback
triggered by the platform_device_unregister call. Add a comment stating
that.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
When users register an event the name of the event and it's argument are
checked to ensure they match if the event already exists. Normally all
arguments are in the form of "type name", except for when the type
starts with "struct ". In those cases, the size of the struct is passed
in addition to the name, IE: "struct my_struct a 20" for an argument
that is of type "struct my_struct" with a field name of "a" and has the
size of 20 bytes.
The current code does not honor the above case properly when comparing
a match. This causes the event register to fail even when the same
string was used for events that contain a struct argument within them.
The example above "struct my_struct a 20" generates a match string of
"struct my_struct a" omitting the size field.
Add the struct size of the existing field when generating a comparison
string for a struct field to ensure proper match checking.
Link: https://lkml.kernel.org/r/20230629235049.581-2-beaub@linux.microsoft.com
Cc: stable@vger.kernel.org
Fixes: e6f89a149872 ("tracing/user_events: Ensure user provided strings are safely formatted")
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
This is now unused, so can remove it.
Link: https://lore.kernel.org/linux-trace-kernel/20230623091640.21952-1-yuehaibing@huawei.com
Cc: <mark.rutland@arm.com>
Cc: <tglx@linutronix.de>
Cc: <mingo@redhat.com>
Cc: <bp@alien8.de>
Cc: <dave.hansen@linux.intel.com>
Cc: <x86@kernel.org>
Cc: <hpa@zytor.com>
Cc: <peterz@infradead.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
rethook_free()
Ensure running fprobe_exit_handler() has finished before
calling rethook_free() in the unregister_fprobe() so that caller can free
the fprobe right after unregister_fprobe().
unregister_fprobe() ensured that all running fprobe_entry/exit_handler()
have finished by calling unregister_ftrace_function() which synchronizes
RCU. But commit 5f81018753df ("fprobe: Release rethook after the ftrace_ops
is unregistered") changed to call rethook_free() after
unregister_ftrace_function(). So call rethook_stop() to make rethook
disabled before unregister_ftrace_function() and ensure it again.
Here is the possible code flow that can call the exit handler after
unregister_fprobe().
------
CPU1 CPU2
call unregister_fprobe(fp)
...
__fprobe_handler()
rethook_hook() on probed function
unregister_ftrace_function()
return from probed function
rethook hooks
find rh->handler == fprobe_exit_handler
call fprobe_exit_handler()
rethook_free():
set rh->handler = NULL;
return from unreigster_fprobe;
call fp->exit_handler() <- (*)
------
(*) At this point, the exit handler is called after returning from
unregister_fprobe().
This fixes it as following;
------
CPU1 CPU2
call unregister_fprobe()
...
rethook_stop():
set rh->handler = NULL;
__fprobe_handler()
rethook_hook() on probed function
unregister_ftrace_function()
return from probed function
rethook hooks
find rh->handler == NULL
return from rethook
rethook_free()
return from unreigster_fprobe;
------
Link: https://lore.kernel.org/all/168873859949.156157.13039240432299335849.stgit@devnote2/
Fixes: 5f81018753df ("fprobe: Release rethook after the ftrace_ops is unregistered")
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The ftrace samples need per-architecture trampoline implementations
to save and restore argument registers around the calls to
my_direct_func* and to restore polluted registers (eg: x30).
These samples also include <asm/asm-offsets.h> which, on arm64, is not
necessary and redefines previously defined macros (resulting in
warnings) so these includes are guarded by !CONFIG_ARM64.
Link: https://lkml.kernel.org/r/20230427140700.625241-3-revest@chromium.org
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
The ftrace-direct-too sample traces the handle_mm_fault function whose
signature changed since the introduction of the sample. Since:
commit bce617edecad ("mm: do page fault accounting in handle_mm_fault")
handle_mm_fault now has 4 arguments. Therefore, the sample trampoline
should save 4 argument registers.
s390 saves all argument registers already so it does not need a change
but x86_64 needs an extra push and pop.
This also evolves the signature of the tracing function to make it
mirror the signature of the traced function.
Link: https://lkml.kernel.org/r/20230427140700.625241-2-revest@chromium.org
Cc: stable@vger.kernel.org
Fixes: bce617edecad ("mm: do page fault accounting in handle_mm_fault")
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
With commit 27267655c531 ("openrisc: Support floating point user api") I
added an entry to the struct sigcontext which caused an unwanted change
to the userspace ABI.
To fix this we use the previously unused oldmask field space for the
floating point fpcsr state. We do this with a union to restore the ABI
back to the pre kernel v6.4 ABI and keep API compatibility.
This does mean if there is some code somewhere that is setting oldmask
in an OpenRISC specific userspace sighandler it would end up setting the
floating point register status, but I think it's unlikely as oldmask was
never functional before.
Fixes: 27267655c531 ("openrisc: Support floating point user api")
Reported-by: Szabolcs Nagy <nsz@port70.net>
Closes: https://lore.kernel.org/openrisc/20230626213840.GA1236108@port70.net/
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog update from Wim Van Sebroeck:
- Add Loongson-1 watchdog dt-bindings
* tag 'linux-watchdog-6.5-rc2' of git://www.linux-watchdog.org/linux-watchdog:
dt-bindings: watchdog: Add Loongson-1 watchdog
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix a couple of regressions in af_alg and incorrect return values in
crypto/asymmetric_keys/public_key"
* tag 'v6.5-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: algif_hash - Fix race between MORE and non-MORE sends
KEYS: asymmetric: Fix error codes
crypto: af_alg - Fix merging of written data into spliced pages
|
|
It's no longer used. While in there, also update the comment as to why
it can coexist with the rb_node.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
As per NVMe command set specification 1.0c Storage tag size is 7 bits.
Fixes: 4020aad85c67 ("nvme: add support for enhanced metadata")
Signed-off-by: Ankit Kumar <ankit.kumar@samsung.com>
Reviewed-by: Kanchan Joshi <joshi.k@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The insertion of an empty frame was introduced with
commit db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02ba ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END
prevent the packet transmission over slot and cycle boundaries.
This is important for taprio offload where the slots and
cycles correspond to the slots and cycles configured for the
network.
However, the Qbv offload feature of the i225 is also used for
enabling TX launchtime / ETF offload. In that case, however,
the cycle has no meaning for the network and is only used
internally to adapt the base time register after a second has
passed.
Enabling strict mode in this case would unnecessarily prevent
the transmission of certain packets (i.e. at the boundary of a
second) and thus interferes with the ETF qdisc that promises
transmission at a certain point in time.
Similar to ETF, this also applies to CBS offload that also should
not be influenced by strict mode unless taprio offload would be
enabled at the same time.
This fully reverts
commit d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling")
but its commit message only describes what was already implemented
before that commit. The difference to a plain revert of that commit
is that it now copes with the base_time = 0 case that was fixed with
commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
In particular, enabling strict mode leads to TX hang situations
under high traffic if taprio is applied WITHOUT taprio offload
but WITH ETF offload, e.g. as in
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <d0>
TDT <f0>
next_to_use <f0>
next_to_clean <d0>
buffer_info[next_to_clean]
time_stamp <ffff661f>
next_to_watch <00000000245a4efb>
jiffies <ffff6e48>
desc.status <1048000>
Fixes: d8f45be01dd9 ("igc: Use strict cycles for Qbv scheduling")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
it is assigned first, so it does not need to initialize the assignment.
Link: https://lore.kernel.org/all/20230711185353.3218-1-zeming@nfschina.com/
Signed-off-by: Li zeming <zeming@nfschina.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
The 'correct_ret_addr' pointer is always set in the later code, no need
to initialize it at definition time.
Link: https://lore.kernel.org/all/20230704194359.3124-1-zeming@nfschina.com/
Signed-off-by: Li zeming <zeming@nfschina.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Unlock ftrace recursion lock when fprobe_kprobe_handler() is failed
because of some running kprobe.
Link: https://lore.kernel.org/all/20230703092336.268371-1-zegao@tencent.com/
Fixes: 3cc4e2c5fbae ("fprobe: make fprobe_kprobe_handler recursion free")
Reported-by: Yafang <laoar.shao@gmail.com>
Closes: https://lore.kernel.org/linux-trace-kernel/CALOAHbC6UpfFOOibdDiC7xFc5YFUgZnk3MZ=3Ny6we=AcrNbew@mail.gmail.com/
Signed-off-by: Ze Gao <zegao@tencent.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Yafang Shao <laoar.shao@gmail.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Replace occurences of the pattern "PAGE_SHIFT - 9" in the passthru and
loop targets with PAGE_SECTORS_SHIFT.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The enable_trace_eprobe() function enables all event probes, attached
to given trace probe. If an error occurs in enabling one of the event
probes, all others should be roll backed. There is a bug in that roll
back logic - instead of all event probes, only the failed one is
disabled.
Link: https://lore.kernel.org/all/20230703042853.1427493-1-tz.stoyanov@gmail.com/
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 7491e2c44278 ("tracing: Add a probe that attaches to trace events")
Signed-off-by: Tzvetomir Stoyanov (VMware) <tz.stoyanov@gmail.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Add the quirk as SM953 is reporting bogus namespace ID.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217593
Reported-by: Clemens Springsguth <cspringsguth@gmail.com>
Tested-by: Clemens Springsguth <cspringsguth@gmail.com>
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
it is possible to enable taprio offload with a basetime of 0.
However, the check if taprio offload is already enabled (and thus -EALREADY
should be returned for igc_save_qbv_schedule) still relied on
adapter->base_time > 0.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and base-time = 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
# The second call should fail with "Error: Device failed to setup taprio offload."
# But that only happens if base-time was != 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb2494 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If defer close timeout value is set to 0, then there is no
need to include files in the deferred close list and utilize
the delayed worker for closing. Instead, we can close them
immediately.
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
skl_int3472_regulator_second_sensor storage-class-specifier to static
smatch reports
drivers/platform/x86/intel/int3472/clk_and_regulator.c:263:28: warning: symbol
'skl_int3472_regulator_second_sensor' was not declared. Should it be static?
This variable is only used in its defining file, so it should be static.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230702134419.3438361-1-trix@redhat.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
cap_offset is a u16 field, so multiplying with TPMI_CAP_OFFSET_UNIT
(which is equal to 1024) to covert to bytes will cause overflow. This
will be a problem once more TPMI features are added.
This field is not used except for calculating pfs->vsec_offset. So, leave
cap_offset field unchanged and multiply with TPMI_CAP_OFFSET_UNIT while
calculating pfs->vsec_offset.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230622195717.3125088-1-srinivas.pandruvada@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Even though we have no issues in the code, let's replace the open
coded guid_parse_and_compare().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-2-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The while-loop may break on one of the two conditions, either ID string
is empty or GUID matches. The second one, may never be reached if the
parsed string is not correct GUID. In such a case the loop will never
advance to check the next ID.
Break possible infinite loop by factoring out guid_parse_and_compare()
helper which may be moved to the generic header for everyone later on
and preventing from similar mistake in the future.
Interestingly that firstly it appeared when WMI was turned into a bus
driver, but later when duplicated GUIDs were checked, the while-loop
has been replaced by for-loop and hence no mistake made again.
Fixes: a48e23385fcf ("platform/x86: wmi: add context pointer field to struct wmi_device_id")
Fixes: 844af950da94 ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230621151155.78279-1-andriy.shevchenko@linux.intel.com
Tested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
There is a small window where we have already incremented the pin count
but not yet moved the bo from the lru to the pinned list.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: Pelloux-Prayer, Pierre-Eric <Pierre-eric.Pelloux-prayer@amd.com>
Tested-by: Pelloux-Prayer, Pierre-Eric <Pierre-eric.Pelloux-prayer@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20230707120826.3701-1-christian.koenig@amd.com
|
|
The command word is defined as following:
/* Command */
#define SPI_CMD_COMMAND_SHIFT 0
#define SPI_CMD_DEVICE_ID_SHIFT 4
#define SPI_CMD_PREPEND_BYTE_CNT_SHIFT 8
#define SPI_CMD_ONE_BYTE_SHIFT 11
#define SPI_CMD_ONE_WIRE_SHIFT 12
If the prepend byte count field starts at bit 8, and the next defined
bit is SPI_CMD_ONE_BYTE at bit 11, it can be at most 3 bits wide, and
thus the max value is 7, not 15.
Fixes: b17de076062a ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230629071453.62024-1-jonas.gorski@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Tudor is not with Microchip anymore. I have worked lately
with Microchip SPI drivers replacing Tudor with myself as this
maintainer.
Signed-off-by: Ryan Wanner <Ryan.Wanner@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20230630161700.448747-1-Ryan.Wanner@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, sd1 and sd0 have unique subnode names 'sd1_mux' and 'sd0_mux'.
If we change these to non-unique subnode names such as 'mux' this can
lead to the below conflict as the RZ/G2L pin control driver considers
only the names of the subnodes.
pinctrl-rzg2l 11030000.pinctrl: pin P47_0 already requested by 11c00000.mmc; cannot claim for 11c10000.mmc
pinctrl-rzg2l 11030000.pinctrl: pin-376 (11c10000.mmc) status -22
pinctrl-rzg2l 11030000.pinctrl: could not request pin 376 (P47_0) from group mux on device pinctrl-rzg2l
renesas_sdhi_internal_dmac 11c10000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Based on the work done by Geert for the RZ/V2M pinctrl driver.
Fixes: c4c4637eb57f ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230704111858.215278-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The eMMC and SDHI pin control configuration nodes in DT have subnodes
with the same names ("data" and "ctrl"). As the RZ/V2M pin control
driver considers only the names of the subnodes, this leads to
conflicts:
pinctrl-rzv2m b6250000.pinctrl: pin P8_2 already requested by 85000000.mmc; cannot claim for 85020000.mmc
pinctrl-rzv2m b6250000.pinctrl: pin-130 (85020000.mmc) status -22
renesas_sdhi_internal_dmac 85020000.mmc: Error applying setting, reverse things back
Fix this by constructing unique names from the node names of both the
pin control configuration node and its child node, where appropriate.
Reported by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Fixes: 92a9b825257614af ("pinctrl: renesas: Add RZ/V2M pin and gpio controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/607bd6ab4905b0b1b119a06ef953fa1184505777.1688396717.git.geert+renesas@glider.be
|
|
Shift operation of 'exp' and 'shift' variables exceeds the maximum number
of shift values in the u32 range leading to UBSAN shift-out-of-bounds.
...
[ 6.120512] UBSAN: shift-out-of-bounds in drivers/hid/amd-sfh-hid/sfh1_1/amd_sfh_desc.c:149:50
[ 6.120598] shift exponent 104 is too large for 64-bit type 'long unsigned int'
[ 6.120659] CPU: 4 PID: 96 Comm: kworker/4:1 Not tainted 6.4.0amd_1-next-20230519-dirty #10
[ 6.120665] Hardware name: AMD Birman-PHX/Birman-PHX, BIOS SFH_with_HPD_SEN.FD 04/05/2023
[ 6.120667] Workqueue: events amd_sfh_work_buffer [amd_sfh]
[ 6.120687] Call Trace:
[ 6.120690] <TASK>
[ 6.120694] dump_stack_lvl+0x48/0x70
[ 6.120704] dump_stack+0x10/0x20
[ 6.120707] ubsan_epilogue+0x9/0x40
[ 6.120716] __ubsan_handle_shift_out_of_bounds+0x10f/0x170
[ 6.120720] ? psi_group_change+0x25f/0x4b0
[ 6.120729] float_to_int.cold+0x18/0xba [amd_sfh]
[ 6.120739] get_input_rep+0x57/0x340 [amd_sfh]
[ 6.120748] ? __schedule+0xba7/0x1b60
[ 6.120756] ? __pfx_get_input_rep+0x10/0x10 [amd_sfh]
[ 6.120764] amd_sfh_work_buffer+0x91/0x180 [amd_sfh]
[ 6.120772] process_one_work+0x229/0x430
[ 6.120780] worker_thread+0x4a/0x3c0
[ 6.120784] ? __pfx_worker_thread+0x10/0x10
[ 6.120788] kthread+0xf7/0x130
[ 6.120792] ? __pfx_kthread+0x10/0x10
[ 6.120795] ret_from_fork+0x29/0x50
[ 6.120804] </TASK>
...
Fix this by adding the condition to validate shift ranges.
Fixes: 93ce5e0231d7 ("HID: amd_sfh: Implement SFH1.1 functionality")
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-3-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
As float32 is also used in other places as a data type, it is necessary
to rename the float32 variable in order to avoid confusion.
Cc: stable@vger.kernel.org
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Link: https://lore.kernel.org/r/20230707065722.9036-2-Basavaraj.Natikar@amd.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Destroying psi trigger in cgroup_file_release causes UAF issues when
a cgroup is removed from under a polling process. This is happening
because cgroup removal causes a call to cgroup_file_release while the
actual file is still alive. Destroying the trigger at this point would
also destroy its waitqueue head and if there is still a polling process
on that file accessing the waitqueue, it will step on the freed pointer:
do_select
vfs_poll
do_rmdir
cgroup_rmdir
kernfs_drain_open_files
cgroup_file_release
cgroup_pressure_release
psi_trigger_destroy
wake_up_pollfree(&t->event_wait)
// vfs_poll is unblocked
synchronize_rcu
kfree(t)
poll_freewait -> UAF access to the trigger's waitqueue head
Patch [1] fixed this issue for epoll() case using wake_up_pollfree(),
however the same issue exists for synchronous poll() case.
The root cause of this issue is that the lifecycles of the psi trigger's
waitqueue and of the file associated with the trigger are different. Fix
this by using kernfs_generic_poll function when polling on cgroup-specific
psi triggers. It internally uses kernfs_open_node->poll waitqueue head
with its lifecycle tied to the file's lifecycle. This also renders the
fix in [1] obsolete, so revert it.
[1] commit c2dbe32d5db5 ("sched/psi: Fix use-after-free in ep_remove_wait_queue()")
Fixes: 0e94682b73bf ("psi: introduce psi monitor")
Closes: https://lore.kernel.org/all/20230613062306.101831-1-lujialin4@huawei.com/
Reported-by: Lu Jialin <lujialin4@huawei.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20230630005612.1014540-1-surenb@google.com
|
|
When checking whether a recently used CPU can be a potential idle
candidate, recent_used_cpu should be used to test p->cpus_ptr as
p->recent_used_cpu is not equal to recent_used_cpu and candidate
decision is made based on recent_used_cpu here.
Fixes: 89aafd67f28c ("sched/fair: Use prev instead of new target as recent_used_cpu")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Phil Auld <pauld@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Link: https://lore.kernel.org/r/20230620080747.359122-1-linmiaohe@huawei.com
|
|
Extend commit 50f9a76ef127 ("iov_iter: Mark
copy_compat_iovec_from_user() noinline") to also cover
copy_iovec_from_user(). Different compiler versions cause the same
problem on different functions.
lib/iov_iter.o: warning: objtool: .altinstr_replacement+0x1f: redundant UACCESS disable
lib/iov_iter.o: warning: objtool: iovec_from_user+0x84: call to copy_iovec_from_user.part.0() with UACCESS enabled
lib/iov_iter.o: warning: objtool: __import_iovec+0x143: call to copy_iovec_from_user.part.0() with UACCESS enabled
Fixes: 50f9a76ef127 ("iov_iter: Mark copy_compat_iovec_from_user() noinline")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lkml.kernel.org/r/20230616124354.GD4253@hirez.programming.kicks-ass.net
|
|
Function elf_open_read() only zero initializes the initial part of
allocated struct elf; num_relocs member was recently added outside the
zeroed part so that it was left uninitialized, resulting in build failures
on some systems.
The partial initialization is a relic of times when struct elf had large
hash tables embedded. This is no longer the case so remove the trap and
initialize the whole structure instead.
Fixes: eb0481bbc4ce ("objtool: Fix reloc_hash size")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20230629102051.42E8360467@lion.mk-sys.cz
|
|
Alyssa noticed that when building the kernel with CFI_CLANG+IBT and
booting on IBT enabled hardware to obtain FineIBT, the indirect
functions look like:
__cfi_foo:
endbr64
subl $hash, %r10d
jz 1f
ud2
nop
1:
foo:
endbr64
This is because the compiler generates code for kCFI+IBT. In that case
the caller does the hash check and will jump to +0, so there must be
an ENDBR there. The compiler doesn't know about FineIBT at all; also
it is possible to actually use kCFI+IBT when booting with 'cfi=kcfi'
on IBT enabled hardware.
Having this second ENDBR however makes it possible to elide the CFI
check. Therefore, we should poison this second ENDBR when switching to
FineIBT mode.
Fixes: 931ab63664f0 ("x86/ibt: Implement FineIBT")
Reported-by: "Milburn, Alyssa" <alyssa.milburn@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20230615193722.194131053@infradead.org
|
|
When kCFI is enabled, special handling is needed for the indirect call
to the kernel thread function. Rewrite the ret_from_fork() function in
C so that the compiler can properly handle the indirect call.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lkml.kernel.org/r/20230623225529.34590-3-brgerst@gmail.com
|
