| Age | Commit message (Collapse) | Author |
|---|
|
commit 7601df8031fd67310af891897ef6cc0df4209305 upstream.
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
do_task_stat() at the same time and the process has NR_THREADS, it will
spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change do_task_stat() to use sig->stats_lock to gather the statistics
outside of ->siglock protected section, in the likely case this code will
run lockless.
Link: https://lkml.kernel.org/r/20240123153357.GA21857@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lock_task_sighand()
commit 60f92acb60a989b14e4b744501a0df0f82ef30a3 upstream.
Patch series "fs/proc: do_task_stat: use sig->stats_".
do_task_stat() has the same problem as getrusage() had before "getrusage:
use sig->stats_lock rather than lock_task_sighand()": a hard lockup. If
NR_CPUS threads call lock_task_sighand() at the same time and the process
has NR_THREADS, spin_lock_irq will spin with irqs disabled O(NR_CPUS *
NR_THREADS) time.
This patch (of 3):
thread_group_cputime() does its own locking, we can safely shift
thread_group_cputime_adjusted() which does another for_each_thread loop
outside of ->siglock protected section.
Not only this removes for_each_thread() from the critical section with
irqs disabled, this removes another case when stats_lock is taken with
siglock held. We want to remove this dependency, then we can change the
users of stats_lock to not disable irqs.
Link: https://lkml.kernel.org/r/20240123153313.GA21832@redhat.com
Link: https://lkml.kernel.org/r/20240123153355.GA21854@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 741ba0134fa7822fcf4e4a0a537a5c4cfd706b20 upstream.
The unused clock cleanup uses the _sync initcall to give all users at
earlier initcalls time to probe. Do the same to avoid leaving some PDs
dangling at "on" (which actually happened on qcom!).
Fixes: 2fe71dcdfd10 ("PM / domains: Add late_initcall to disable unused PM domains")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20231227-topic-pmdomain_sync_cleanup-v1-1-5f36769d538b@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit efe7cf828039aedb297c1f9920b638fffee6aabc upstream.
Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...)
modifies jsk->filters while receiving packets.
Following trace was seen on affected system:
==================================================================
BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
Read of size 4 at addr ffff888012144014 by task j1939/350
CPU: 0 PID: 350 Comm: j1939 Tainted: G W OE 6.5.0-rc5 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
print_report+0xd3/0x620
? kasan_complete_mode_report_info+0x7d/0x200
? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
kasan_report+0xc2/0x100
? j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
__asan_load4+0x84/0xb0
j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
j1939_sk_recv+0x20b/0x320 [can_j1939]
? __kasan_check_write+0x18/0x20
? __pfx_j1939_sk_recv+0x10/0x10 [can_j1939]
? j1939_simple_recv+0x69/0x280 [can_j1939]
? j1939_ac_recv+0x5e/0x310 [can_j1939]
j1939_can_recv+0x43f/0x580 [can_j1939]
? __pfx_j1939_can_recv+0x10/0x10 [can_j1939]
? raw_rcv+0x42/0x3c0 [can_raw]
? __pfx_j1939_can_recv+0x10/0x10 [can_j1939]
can_rcv_filter+0x11f/0x350 [can]
can_receive+0x12f/0x190 [can]
? __pfx_can_rcv+0x10/0x10 [can]
can_rcv+0xdd/0x130 [can]
? __pfx_can_rcv+0x10/0x10 [can]
__netif_receive_skb_one_core+0x13d/0x150
? __pfx___netif_receive_skb_one_core+0x10/0x10
? __kasan_check_write+0x18/0x20
? _raw_spin_lock_irq+0x8c/0xe0
__netif_receive_skb+0x23/0xb0
process_backlog+0x107/0x260
__napi_poll+0x69/0x310
net_rx_action+0x2a1/0x580
? __pfx_net_rx_action+0x10/0x10
? __pfx__raw_spin_lock+0x10/0x10
? handle_irq_event+0x7d/0xa0
__do_softirq+0xf3/0x3f8
do_softirq+0x53/0x80
</IRQ>
<TASK>
__local_bh_enable_ip+0x6e/0x70
netif_rx+0x16b/0x180
can_send+0x32b/0x520 [can]
? __pfx_can_send+0x10/0x10 [can]
? __check_object_size+0x299/0x410
raw_sendmsg+0x572/0x6d0 [can_raw]
? __pfx_raw_sendmsg+0x10/0x10 [can_raw]
? apparmor_socket_sendmsg+0x2f/0x40
? __pfx_raw_sendmsg+0x10/0x10 [can_raw]
sock_sendmsg+0xef/0x100
sock_write_iter+0x162/0x220
? __pfx_sock_write_iter+0x10/0x10
? __rtnl_unlock+0x47/0x80
? security_file_permission+0x54/0x320
vfs_write+0x6ba/0x750
? __pfx_vfs_write+0x10/0x10
? __fget_light+0x1ca/0x1f0
? __rcu_read_unlock+0x5b/0x280
ksys_write+0x143/0x170
? __pfx_ksys_write+0x10/0x10
? __kasan_check_read+0x15/0x20
? fpregs_assert_state_consistent+0x62/0x70
__x64_sys_write+0x47/0x60
do_syscall_64+0x60/0x90
? do_syscall_64+0x6d/0x90
? irqentry_exit+0x3f/0x50
? exc_page_fault+0x79/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Allocated by task 348:
kasan_save_stack+0x2a/0x50
kasan_set_track+0x29/0x40
kasan_save_alloc_info+0x1f/0x30
__kasan_kmalloc+0xb5/0xc0
__kmalloc_node_track_caller+0x67/0x160
j1939_sk_setsockopt+0x284/0x450 [can_j1939]
__sys_setsockopt+0x15c/0x2f0
__x64_sys_setsockopt+0x6b/0x80
do_syscall_64+0x60/0x90
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Freed by task 349:
kasan_save_stack+0x2a/0x50
kasan_set_track+0x29/0x40
kasan_save_free_info+0x2f/0x50
__kasan_slab_free+0x12e/0x1c0
__kmem_cache_free+0x1b9/0x380
kfree+0x7a/0x120
j1939_sk_setsockopt+0x3b2/0x450 [can_j1939]
__sys_setsockopt+0x15c/0x2f0
__x64_sys_setsockopt+0x6b/0x80
do_syscall_64+0x60/0x90
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Fixes: 9d71dd0c70099 ("can: add support of SAE J1939 protocol")
Reported-by: Sili Luo <rootlab@huawei.com>
Suggested-by: Sili Luo <rootlab@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20231020133814.383996-1-o.rempel@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6cdedc18ba7b9dacc36466e27e3267d201948c8d upstream.
The following 3 locks would race against each other, causing the
deadlock situation in the Syzbot bug report:
- j1939_socks_lock
- active_session_list_lock
- sk_session_queue_lock
A reasonable fix is to change j1939_socks_lock to an rwlock, since in
the rare situations where a write lock is required for the linked list
that j1939_socks_lock is protecting, the code does not attempt to
acquire any more locks. This would break the circular lock dependency,
where, for example, the current thread already locks j1939_socks_lock
and attempts to acquire sk_session_queue_lock, and at the same time,
another thread attempts to acquire j1939_socks_lock while holding
sk_session_queue_lock.
NOTE: This patch along does not fix the unregister_netdevice bug
reported by Syzbot; instead, it solves a deadlock situation to prepare
for one or more further patches to actually fix the Syzbot bug, which
appears to be a reference counting problem within the j1939 codebase.
Reported-by: <syzbot+1591462f226d9cbf0564@syzkaller.appspotmail.com>
Signed-off-by: Ziqi Zhao <astrajoan@yahoo.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20230721162226.8639-1-astrajoan@yahoo.com
[mkl: remove unrelated newline change]
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2aa0a5e65eae27dbd96faca92c84ecbf6f492d42 upstream.
The TDCO calculation was done using the currently applied data bittiming,
instead of the newly computed data bittiming, which means that the TDCO
had an invalid value unless setting the same data bittiming twice.
Fixes: d99755f71a80 ("can: netlink: add interface for CAN-FD Transmitter Delay Compensation (TDC)")
Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/40579c18-63c0-43a4-8d4c-f3a6c1c0b417@munic.io
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fa765c4b4aed2d64266b694520ecb025c862c5a9 upstream.
shutdown_pirq and startup_pirq are not taking the
irq_mapping_update_lock because they can't due to lock inversion. Both
are called with the irq_desc->lock being taking. The lock order,
however, is first irq_mapping_update_lock and then irq_desc->lock.
This opens multiple races:
- shutdown_pirq can be interrupted by a function that allocates an event
channel:
CPU0 CPU1
shutdown_pirq {
xen_evtchn_close(e)
__startup_pirq {
EVTCHNOP_bind_pirq
-> returns just freed evtchn e
set_evtchn_to_irq(e, irq)
}
xen_irq_info_cleanup() {
set_evtchn_to_irq(e, -1)
}
}
Assume here event channel e refers here to the same event channel
number.
After this race the evtchn_to_irq mapping for e is invalid (-1).
- __startup_pirq races with __unbind_from_irq in a similar way. Because
__startup_pirq doesn't take irq_mapping_update_lock it can grab the
evtchn that __unbind_from_irq is currently freeing and cleaning up. In
this case even though the event channel is allocated, its mapping can
be unset in evtchn_to_irq.
The fix is to first cleanup the mappings and then close the event
channel. In this way, when an event channel gets allocated it's
potential previous evtchn_to_irq mappings are guaranteed to be unset already.
This is also the reverse order of the allocation where first the event
channel is allocated and then the mappings are setup.
On a 5.10 kernel prior to commit 3fcdaf3d7634 ("xen/events: modify internal
[un]bind interfaces"), we hit a BUG like the following during probing of NVMe
devices. The issue is that during nvme_setup_io_queues, pci_free_irq
is called for every device which results in a call to shutdown_pirq.
With many nvme devices it's therefore likely to hit this race during
boot because there will be multiple calls to shutdown_pirq and
startup_pirq are running potentially in parallel.
------------[ cut here ]------------
blkfront: xvda: barrier or flush: disabled; persistent grants: enabled; indirect descriptors: enabled; bounce buffer: enabled
kernel BUG at drivers/xen/events/events_base.c:499!
invalid opcode: 0000 [#1] SMP PTI
CPU: 44 PID: 375 Comm: kworker/u257:23 Not tainted 5.10.201-191.748.amzn2.x86_64 #1
Hardware name: Xen HVM domU, BIOS 4.11.amazon 08/24/2006
Workqueue: nvme-reset-wq nvme_reset_work
RIP: 0010:bind_evtchn_to_cpu+0xdf/0xf0
Code: 5d 41 5e c3 cc cc cc cc 44 89 f7 e8 2b 55 ad ff 49 89 c5 48 85 c0 0f 84 64 ff ff ff 4c 8b 68 30 41 83 fe ff 0f 85 60 ff ff ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 0f 1f 44 00 00
RSP: 0000:ffffc9000d533b08 EFLAGS: 00010046
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000006
RDX: 0000000000000028 RSI: 00000000ffffffff RDI: 00000000ffffffff
RBP: ffff888107419680 R08: 0000000000000000 R09: ffffffff82d72b00
R10: 0000000000000000 R11: 0000000000000000 R12: 00000000000001ed
R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffff88bc8b500000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 0000000002610001 CR4: 00000000001706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
? show_trace_log_lvl+0x1c1/0x2d9
? show_trace_log_lvl+0x1c1/0x2d9
? set_affinity_irq+0xdc/0x1c0
? __die_body.cold+0x8/0xd
? die+0x2b/0x50
? do_trap+0x90/0x110
? bind_evtchn_to_cpu+0xdf/0xf0
? do_error_trap+0x65/0x80
? bind_evtchn_to_cpu+0xdf/0xf0
? exc_invalid_op+0x4e/0x70
? bind_evtchn_to_cpu+0xdf/0xf0
? asm_exc_invalid_op+0x12/0x20
? bind_evtchn_to_cpu+0xdf/0xf0
? bind_evtchn_to_cpu+0xc5/0xf0
set_affinity_irq+0xdc/0x1c0
irq_do_set_affinity+0x1d7/0x1f0
irq_setup_affinity+0xd6/0x1a0
irq_startup+0x8a/0xf0
__setup_irq+0x639/0x6d0
? nvme_suspend+0x150/0x150
request_threaded_irq+0x10c/0x180
? nvme_suspend+0x150/0x150
pci_request_irq+0xa8/0xf0
? __blk_mq_free_request+0x74/0xa0
queue_request_irq+0x6f/0x80
nvme_create_queue+0x1af/0x200
nvme_create_io_queues+0xbd/0xf0
nvme_setup_io_queues+0x246/0x320
? nvme_irq_check+0x30/0x30
nvme_reset_work+0x1c8/0x400
process_one_work+0x1b0/0x350
worker_thread+0x49/0x310
? process_one_work+0x350/0x350
kthread+0x11b/0x140
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x22/0x30
Modules linked in:
---[ end trace a11715de1eee1873 ]---
Fixes: d46a78b05c0e ("xen: implement pirq type event channels")
Cc: stable@vger.kernel.org
Co-debugged-by: Andrew Panyakin <apanyaki@amazon.com>
Signed-off-by: Maximilian Heyne <mheyne@amazon.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240124163130.31324-1-mheyne@amazon.de
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8f7e917907385e112a845d668ae2832f41e64bf5 upstream.
The property is io-channels and not io-channel. This was effectively
preventing the devlink creation.
Fixes: 8e12257dead7 ("of: property: Add device link support for iommus, mboxes and io-channels")
Cc: stable@vger.kernel.org
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240123-iio-backend-v7-1-1bff236b8693@analog.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c23de7ceae59e4ca5894c3ecf4f785c50c0fa428 upstream.
If the directory passed to the '.. kernel-feat::' directive does not
exist or the get_feat.pl script does not find any files to extract
features from, Sphinx will report the following error:
Sphinx parallel build error:
UnboundLocalError: local variable 'fname' referenced before assignment
make[2]: *** [Documentation/Makefile:102: htmldocs] Error 2
This is due to how I changed the script in c48a7c44a1d0 ("docs:
kernel_feat.py: fix potential command injection"). Before that, the
filename passed along to self.nestedParse() in this case was weirdly
just the whole get_feat.pl invocation.
We can fix it by doing what kernel_abi.py does -- just pass
self.arguments[0] as 'fname'.
Fixes: c48a7c44a1d0 ("docs: kernel_feat.py: fix potential command injection")
Cc: Justin Forbes <jforbes@fedoraproject.org>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Link: https://lore.kernel.org/r/20240205175133.774271-2-vegard.nossum@oracle.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f814bdda774c183b0cc15ec8f3b6e7c6f4527ba5 upstream.
The detection of dirty-throttled tasks in blk-wbt has been subtly broken
since its beginning in 2016. Namely if we are doing cgroup writeback and
the throttled task is not in the root cgroup, balance_dirty_pages() will
set dirty_sleep for the non-root bdi_writeback structure. However
blk-wbt checks dirty_sleep only in the root cgroup bdi_writeback
structure. Thus detection of recently throttled tasks is not working in
this case (we noticed this when we switched to cgroup v2 and suddently
writeback was slow).
Since blk-wbt has no easy way to get to proper bdi_writeback and
furthermore its intention has always been to work on the whole device
rather than on individual cgroups, just move the dirty_sleep timestamp
from bdi_writeback to backing_dev_info. That fixes the checking for
recently throttled task and saves memory for everybody as a bonus.
CC: stable@vger.kernel.org
Fixes: b57d74aff9ab ("writeback: track if we're sleeping on progress in balance_dirty_pages()")
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20240123175826.21452-1-jack@suse.cz
[axboe: fixup indentation errors]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 639420e9f6cd9ca074732b17ac450d2518d5937f upstream.
The earlycon parameter is based on fixmap, and fixmap addresses are not
supposed to be shadowed by KASAN. So return the kasan_early_shadow_page
in kasan_mem_to_shadow() if the input address is above FIXADDR_START.
Otherwise earlycon cannot work after kasan_init().
Cc: stable@vger.kernel.org
Fixes: 5aa4ac64e6add3e ("LoongArch: Add KASAN (Kernel Address Sanitizer) support")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e656c7a9e59607d1672d85ffa9a89031876ffe67 upstream.
For shared memory of type SHM_HUGETLB, hugetlb pages are reserved in
shmget() call. If SHM_NORESERVE flags is specified then the hugetlb pages
are not reserved. However when the shared memory is attached with the
shmat() call the hugetlb pages are getting reserved incorrectly for
SHM_HUGETLB shared memory created with SHM_NORESERVE which is a bug.
-------------------------------
Following test shows the issue.
$cat shmhtb.c
int main()
{
int shmflags = 0660 | IPC_CREAT | SHM_HUGETLB | SHM_NORESERVE;
int shmid;
shmid = shmget(SKEY, SHMSZ, shmflags);
if (shmid < 0)
{
printf("shmat: shmget() failed, %d\n", errno);
return 1;
}
printf("After shmget()\n");
system("cat /proc/meminfo | grep -i hugepages_");
shmat(shmid, NULL, 0);
printf("\nAfter shmat()\n");
system("cat /proc/meminfo | grep -i hugepages_");
shmctl(shmid, IPC_RMID, NULL);
return 0;
}
#sysctl -w vm.nr_hugepages=20
#./shmhtb
After shmget()
HugePages_Total: 20
HugePages_Free: 20
HugePages_Rsvd: 0
HugePages_Surp: 0
After shmat()
HugePages_Total: 20
HugePages_Free: 20
HugePages_Rsvd: 5 <--
HugePages_Surp: 0
--------------------------------
Fix is to ensure that hugetlb pages are not reserved for SHM_HUGETLB shared
memory in the shmat() call.
Link: https://lkml.kernel.org/r/1706040282-12388-1-git-send-email-prakash.sangappa@oracle.com
Signed-off-by: Prakash Sangappa <prakash.sangappa@oracle.com>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 79d72c68c58784a3e1cd2378669d51bfd0cb7498 upstream.
When configuring a hugetlb filesystem via the fsconfig() syscall, there is
a possible NULL dereference in hugetlbfs_fill_super() caused by assigning
NULL to ctx->hstate in hugetlbfs_parse_param() when the requested pagesize
is non valid.
E.g: Taking the following steps:
fd = fsopen("hugetlbfs", FSOPEN_CLOEXEC);
fsconfig(fd, FSCONFIG_SET_STRING, "pagesize", "1024", 0);
fsconfig(fd, FSCONFIG_CMD_CREATE, NULL, NULL, 0);
Given that the requested "pagesize" is invalid, ctxt->hstate will be replaced
with NULL, losing its previous value, and we will print an error:
...
...
case Opt_pagesize:
ps = memparse(param->string, &rest);
ctx->hstate = h;
if (!ctx->hstate) {
pr_err("Unsupported page size %lu MB\n", ps / SZ_1M);
return -EINVAL;
}
return 0;
...
...
This is a problem because later on, we will dereference ctxt->hstate in
hugetlbfs_fill_super()
...
...
sb->s_blocksize = huge_page_size(ctx->hstate);
...
...
Causing below Oops.
Fix this by replacing cxt->hstate value only when then pagesize is known
to be valid.
kernel: hugetlbfs: Unsupported page size 0 MB
kernel: BUG: kernel NULL pointer dereference, address: 0000000000000028
kernel: #PF: supervisor read access in kernel mode
kernel: #PF: error_code(0x0000) - not-present page
kernel: PGD 800000010f66c067 P4D 800000010f66c067 PUD 1b22f8067 PMD 0
kernel: Oops: 0000 [#1] PREEMPT SMP PTI
kernel: CPU: 4 PID: 5659 Comm: syscall Tainted: G E 6.8.0-rc2-default+ #22 5a47c3fef76212addcc6eb71344aabc35190ae8f
kernel: Hardware name: Intel Corp. GROVEPORT/GROVEPORT, BIOS GVPRCRB1.86B.0016.D04.1705030402 05/03/2017
kernel: RIP: 0010:hugetlbfs_fill_super+0xb4/0x1a0
kernel: Code: 48 8b 3b e8 3e c6 ed ff 48 85 c0 48 89 45 20 0f 84 d6 00 00 00 48 b8 ff ff ff ff ff ff ff 7f 4c 89 e7 49 89 44 24 20 48 8b 03 <8b> 48 28 b8 00 10 00 00 48 d3 e0 49 89 44 24 18 48 8b 03 8b 40 28
kernel: RSP: 0018:ffffbe9960fcbd48 EFLAGS: 00010246
kernel: RAX: 0000000000000000 RBX: ffff9af5272ae780 RCX: 0000000000372004
kernel: RDX: ffffffffffffffff RSI: ffffffffffffffff RDI: ffff9af555e9b000
kernel: RBP: ffff9af52ee66b00 R08: 0000000000000040 R09: 0000000000370004
kernel: R10: ffffbe9960fcbd48 R11: 0000000000000040 R12: ffff9af555e9b000
kernel: R13: ffffffffa66b86c0 R14: ffff9af507d2f400 R15: ffff9af507d2f400
kernel: FS: 00007ffbc0ba4740(0000) GS:ffff9b0bd7000000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 0000000000000028 CR3: 00000001b1ee0000 CR4: 00000000001506f0
kernel: Call Trace:
kernel: <TASK>
kernel: ? __die_body+0x1a/0x60
kernel: ? page_fault_oops+0x16f/0x4a0
kernel: ? search_bpf_extables+0x65/0x70
kernel: ? fixup_exception+0x22/0x310
kernel: ? exc_page_fault+0x69/0x150
kernel: ? asm_exc_page_fault+0x22/0x30
kernel: ? __pfx_hugetlbfs_fill_super+0x10/0x10
kernel: ? hugetlbfs_fill_super+0xb4/0x1a0
kernel: ? hugetlbfs_fill_super+0x28/0x1a0
kernel: ? __pfx_hugetlbfs_fill_super+0x10/0x10
kernel: vfs_get_super+0x40/0xa0
kernel: ? __pfx_bpf_lsm_capable+0x10/0x10
kernel: vfs_get_tree+0x25/0xd0
kernel: vfs_cmd_create+0x64/0xe0
kernel: __x64_sys_fsconfig+0x395/0x410
kernel: do_syscall_64+0x80/0x160
kernel: ? syscall_exit_to_user_mode+0x82/0x240
kernel: ? do_syscall_64+0x8d/0x160
kernel: ? syscall_exit_to_user_mode+0x82/0x240
kernel: ? do_syscall_64+0x8d/0x160
kernel: ? exc_page_fault+0x69/0x150
kernel: entry_SYSCALL_64_after_hwframe+0x6e/0x76
kernel: RIP: 0033:0x7ffbc0cb87c9
kernel: Code: 00 90 90 90 90 90 90 90 90 90 90 90 90 90 90 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 97 96 0d 00 f7 d8 64 89 01 48
kernel: RSP: 002b:00007ffc29d2f388 EFLAGS: 00000206 ORIG_RAX: 00000000000001af
kernel: RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007ffbc0cb87c9
kernel: RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000000000003
kernel: RBP: 00007ffc29d2f3b0 R08: 0000000000000000 R09: 0000000000000000
kernel: R10: 0000000000000000 R11: 0000000000000206 R12: 0000000000000000
kernel: R13: 00007ffc29d2f4c0 R14: 0000000000000000 R15: 0000000000000000
kernel: </TASK>
kernel: Modules linked in: rpcsec_gss_krb5(E) auth_rpcgss(E) nfsv4(E) dns_resolver(E) nfs(E) lockd(E) grace(E) sunrpc(E) netfs(E) af_packet(E) bridge(E) stp(E) llc(E) iscsi_ibft(E) iscsi_boot_sysfs(E) intel_rapl_msr(E) intel_rapl_common(E) iTCO_wdt(E) intel_pmc_bxt(E) sb_edac(E) iTCO_vendor_support(E) x86_pkg_temp_thermal(E) intel_powerclamp(E) coretemp(E) kvm_intel(E) rfkill(E) ipmi_ssif(E) kvm(E) acpi_ipmi(E) irqbypass(E) pcspkr(E) igb(E) ipmi_si(E) mei_me(E) i2c_i801(E) joydev(E) intel_pch_thermal(E) i2c_smbus(E) dca(E) lpc_ich(E) mei(E) ipmi_devintf(E) ipmi_msghandler(E) acpi_pad(E) tiny_power_button(E) button(E) fuse(E) efi_pstore(E) configfs(E) ip_tables(E) x_tables(E) ext4(E) mbcache(E) jbd2(E) hid_generic(E) usbhid(E) sd_mod(E) t10_pi(E) crct10dif_pclmul(E) crc32_pclmul(E) crc32c_intel(E) polyval_clmulni(E) ahci(E) xhci_pci(E) polyval_generic(E) gf128mul(E) ghash_clmulni_intel(E) sha512_ssse3(E) sha256_ssse3(E) xhci_pci_renesas(E) libahci(E) ehci_pci(E) sha1_ssse3(E) xhci_hcd(E) ehci_hcd(E) libata(E)
kernel: mgag200(E) i2c_algo_bit(E) usbcore(E) wmi(E) sg(E) dm_multipath(E) dm_mod(E) scsi_dh_rdac(E) scsi_dh_emc(E) scsi_dh_alua(E) scsi_mod(E) scsi_common(E) aesni_intel(E) crypto_simd(E) cryptd(E)
kernel: Unloaded tainted modules: acpi_cpufreq(E):1 fjes(E):1
kernel: CR2: 0000000000000028
kernel: ---[ end trace 0000000000000000 ]---
kernel: RIP: 0010:hugetlbfs_fill_super+0xb4/0x1a0
kernel: Code: 48 8b 3b e8 3e c6 ed ff 48 85 c0 48 89 45 20 0f 84 d6 00 00 00 48 b8 ff ff ff ff ff ff ff 7f 4c 89 e7 49 89 44 24 20 48 8b 03 <8b> 48 28 b8 00 10 00 00 48 d3 e0 49 89 44 24 18 48 8b 03 8b 40 28
kernel: RSP: 0018:ffffbe9960fcbd48 EFLAGS: 00010246
kernel: RAX: 0000000000000000 RBX: ffff9af5272ae780 RCX: 0000000000372004
kernel: RDX: ffffffffffffffff RSI: ffffffffffffffff RDI: ffff9af555e9b000
kernel: RBP: ffff9af52ee66b00 R08: 0000000000000040 R09: 0000000000370004
kernel: R10: ffffbe9960fcbd48 R11: 0000000000000040 R12: ffff9af555e9b000
kernel: R13: ffffffffa66b86c0 R14: ffff9af507d2f400 R15: ffff9af507d2f400
kernel: FS: 00007ffbc0ba4740(0000) GS:ffff9b0bd7000000(0000) knlGS:0000000000000000
kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
kernel: CR2: 0000000000000028 CR3: 00000001b1ee0000 CR4: 00000000001506f0
Link: https://lkml.kernel.org/r/20240130210418.3771-1-osalvador@suse.de
Fixes: 32021982a324 ("hugetlbfs: Convert to fs_context")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Acked-by: Muchun Song <muchun.song@linux.dev>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61712c94782ce105253ee1939cda0c5c025b2c0c upstream.
Timur pointed this out before, and it just slipped my mind,
but this might help some things work better, around pcie power
management.
Cc: <stable@vger.kernel.org> # v6.7
Fixes: 8d55b0a940bb ("nouveau/gsp: add some basic registry entries.")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240130032643.2498315-1-airlied@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cda4672da1c26835dcbd7aec2bfed954eda9b5ef upstream.
In fs/ceph/caps.c, in encode_cap_msg(), "use after free" error was
caught by KASAN at this line - 'ceph_buffer_get(arg->xattr_buf);'. This
implies before the refcount could be increment here, it was freed.
In same file, in "handle_cap_grant()" refcount is decremented by this
line - 'ceph_buffer_put(ci->i_xattrs.blob);'. It appears that a race
occurred and resource was freed by the latter line before the former
line could increment it.
encode_cap_msg() is called by __send_cap() and __send_cap() is called by
ceph_check_caps() after calling __prep_cap(). __prep_cap() is where
arg->xattr_buf is assigned to ci->i_xattrs.blob. This is the spot where
the refcount must be increased to prevent "use after free" error.
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/59259
Signed-off-by: Rishabh Dave <ridave@redhat.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9cae43da9867412f8bd09aee5c8a8dc5e8dc3dc2 upstream.
If hv_netvsc driver is unloaded and reloaded, the NET_DEVICE_REGISTER
handler cannot perform VF register successfully as the register call
is received before netvsc_probe is finished. This is because we
register register_netdevice_notifier() very early( even before
vmbus_driver_register()).
To fix this, we try to register each such matching VF( if it is visible
as a netdevice) at the end of netvsc_probe.
Cc: stable@vger.kernel.org
Fixes: 85520856466e ("hv_netvsc: Fix race of register_netdevice_notifier and VF register")
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 38cc3c6dcc09dc3a1800b5ec22aef643ca11eab8 upstream.
As explained by a comment in <linux/u64_stats_sync.h>, write side of struct
u64_stats_sync must ensure mutual exclusion, or one seqcount update could
be lost on 32-bit platforms, thus blocking readers forever. Such lockups
have been observed in real world after stmmac_xmit() on one CPU raced with
stmmac_napi_poll_tx() on another CPU.
To fix the issue without introducing a new lock, split the statics into
three parts:
1. fields updated only under the tx queue lock,
2. fields updated only during NAPI poll,
3. fields updated only from interrupt context,
Updates to fields in the first two groups are already serialized through
other locks. It is sufficient to split the existing struct u64_stats_sync
so that each group has its own.
Note that tx_set_ic_bit is updated from both contexts. Split this counter
so that each context gets its own, and calculate their sum to get the total
value in stmmac_get_ethtool_stats().
For the third group, multiple interrupts may be processed by different CPUs
at the same time, but interrupts on the same CPU will not nest. Move fields
from this group to a newly created per-cpu struct stmmac_pcpu_stats.
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Link: https://lore.kernel.org/netdev/Za173PhviYg-1qIn@torres.zugschlus.de/t/
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit afb2a4fb84555ef9e61061f6ea63ed7087b295d5 upstream.
The cflags for the RISC-V efistub were missing -mno-relax, thus were
under the risk that the compiler could use GP-relative addressing. That
happened for _edata with binutils-2.41 and kernel 6.1, causing the
relocation to fail due to an invalid kernel_size in handle_kernel_image.
It was not yet observed with newer versions, but that may just be luck.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f0e4a1356466ec1858ae8e5c70bea2ce5e55008b upstream.
The power domain containing the Cortex-R7 CPU core on the R-Car V3H SoC
must always be in power-on state, unlike on other SoCs in the R-Car Gen3
family. See Table 9.4 "Power domains" in the R-Car Series, 3rd
Generation Hardware User’s Manual Rev.1.00 and later.
Fix this by marking the domain as a CPU domain without control
registers, so the driver will not touch it.
Fixes: 41d6d8bd8ae9 ("soc: renesas: rcar-sysc: add R8A77980 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/fdad9a86132d53ecddf72b734dac406915c4edc0.1705076735.git.geert+renesas@glider.be
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9def04e759caa5a3d741891037ae99f81e2fff01 upstream.
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw_new resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9e4bc1046d20e0623a80660ef8627448056f817 upstream.
DAMON sysfs interface's update_schemes_tried_regions command has a timeout
of two apply intervals of the DAMOS scheme. Having zero value DAMOS
scheme apply interval means it will use the aggregation interval as the
value. However, the timeout setup logic is mistakenly using the sampling
interval insted of the aggregartion interval for the case. This could
cause earlier-than-expected timeout of the command. Fix it.
Link: https://lkml.kernel.org/r/20240202191956.88791-1-sj@kernel.org
Fixes: 7d6fa31a2fd7 ("mm/damon/sysfs-schemes: add timeout for update_schemes_tried_regions")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> # 6.7.x
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fe8a236436fe40d8d26a1af8d150fc80f04ee1a upstream.
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc4ce46b1e3d1da4309405cd4afc7c0fcddd0b90 upstream.
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004 005c3fb8 00000001 005c3fb8 00000004 00000001
dfc0: 00000004 005c3fb8 b6f6bba0 00000004 00000004 0059edb8 00000000 00000000
dfe0: 00000004 bed918f0 b6f09bd3 b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 46f5ab762d048dad224436978315cbc2fa79c630 upstream.
When we added mount_setattr() I added additional checks compared to the
legacy do_reconfigure_mnt() and do_change_type() helpers used by regular
mount(2). If that mount had a parent then verify that the caller and the
mount namespace the mount is attached to match and if not make sure that
it's an anonymous mount.
The real rootfs falls into neither category. It is neither an anoymous
mount because it is obviously attached to the initial mount namespace
but it also obviously doesn't have a parent mount. So that means legacy
mount(2) allows changing mount properties on the real rootfs but
mount_setattr(2) blocks this. I never thought much about this but of
course someone on this planet of earth changes properties on the real
rootfs as can be seen in [1].
Since util-linux finally switched to the new mount api in 2.39 not so
long ago it also relies on mount_setattr() and that surfaced this issue
when Fedora 39 finally switched to it. Fix this.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2256843
Link: https://lore.kernel.org/r/20240206-vfs-mount-rootfs-v1-1-19b335eee133@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v5.12+
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bc4cbc9d260ba8358ca63662919f4bb223cb603b upstream.
The following errors are showing up when compiling rtla with clang:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[...]
clang -O -g -DVERSION=\"6.8.0-rc1\" -flto=auto -ffat-lto-objects
-fexceptions -fstack-protector-strong
-fasynchronous-unwind-tables -fstack-clash-protection -Wall
-Werror=format-security -Wp,-D_FORTIFY_SOURCE=2
-Wp,-D_GLIBCXX_ASSERTIONS -Wno-maybe-uninitialized
$(pkg-config --cflags libtracefs) -c -o src/utils.o src/utils.c
clang: warning: optimization flag '-ffat-lto-objects' is not supported [-Wignored-optimization-argument]
warning: unknown warning option '-Wno-maybe-uninitialized'; did you mean '-Wno-uninitialized'? [-Wunknown-warning-option]
1 warning generated.
clang -o rtla -ggdb src/osnoise.o src/osnoise_hist.o src/osnoise_top.o
src/rtla.o src/timerlat_aa.o src/timerlat.o src/timerlat_hist.o
src/timerlat_top.o src/timerlat_u.o src/trace.o src/utils.o $(pkg-config --libs libtracefs)
src/osnoise.o: file not recognized: file format not recognized
clang: error: linker command failed with exit code 1 (use -v to see invocation)
make: *** [Makefile:110: rtla] Error 1
Solve these issues by:
- removing -ffat-lto-objects and -Wno-maybe-uninitialized if using clang
- informing the linker about -flto=auto
Link: https://lore.kernel.org/linux-trace-kernel/567ac1b94effc228ce9a0225b9df7232a9b35b55.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Fixes: 1a7b22ab15eb ("tools/rtla: Build with EXTRA_{C,LD}FLAGS")
Suggested-by: Donald Zickus <dzickus@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64dc40f7523369912d7adb22c8cb655f71610505 upstream.
When compiling rtla with clang, I am getting the following warnings:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[..]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs)
-c -o src/osnoise_hist.o src/osnoise_hist.c
src/osnoise_hist.c:138:6: warning: variable 'bucket' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
138 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~
src/osnoise_hist.c:149:6: note: uninitialized use occurs here
149 | if (bucket < entries)
| ^~~~~~
src/osnoise_hist.c:138:2: note: remove the 'if' if its condition is always true
138 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~~~~~~
139 | bucket = duration / data->bucket_size;
src/osnoise_hist.c:132:12: note: initialize the variable 'bucket' to silence this warning
132 | int bucket;
| ^
| = 0
1 warning generated.
[...]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs)
-c -o src/timerlat_hist.o src/timerlat_hist.c
src/timerlat_hist.c:181:6: warning: variable 'bucket' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
181 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~
src/timerlat_hist.c:204:6: note: uninitialized use occurs here
204 | if (bucket < entries)
| ^~~~~~
src/timerlat_hist.c:181:2: note: remove the 'if' if its condition is always true
181 | if (data->bucket_size)
| ^~~~~~~~~~~~~~~~~~~~~~
182 | bucket = latency / data->bucket_size;
src/timerlat_hist.c:175:12: note: initialize the variable 'bucket' to silence this warning
175 | int bucket;
| ^
| = 0
1 warning generated.
This is a legit warning, but data->bucket_size is always > 0 (see
timerlat_hist_parse_args()), so the if is not necessary.
Remove the unneeded if (data->bucket_size) to avoid the warning.
Link: https://lkml.kernel.org/r/6e1b1665cd99042ae705b3e0fc410858c4c42346.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Donald Zickus <dzickus@redhat.com>
Fixes: 1eeb6328e8b3 ("rtla/timerlat: Add timerlat hist mode")
Fixes: 829a6c0b5698 ("rtla/osnoise: Add the hist mode")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5f319360371087d52070d8f3fc7789e80ce69a6 upstream.
Fix rtla so that the following commands exit with 0 when help is invoked
rtla osnoise top -h
rtla osnoise hist -h
rtla timerlat top -h
rtla timerlat hist -h
Link: https://lore.kernel.org/linux-trace-devel/20240203001607.69703-1-jkacur@redhat.com
Cc: stable@vger.kernel.org
Fixes: 1eeb6328e8b3 ("rtla/timerlat: Add timerlat hist mode")
Signed-off-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 30369084ac6e27479a347899e74f523e6ca29b89 upstream.
clang is reporting this warning:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[...]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs) -c -o src/utils.o src/utils.c
src/utils.c:548:66: warning: 'fscanf' may overflow; destination buffer in argument 3 has size 1024, but the corresponding specifier may require size 1025 [-Wfortify-source]
548 | while (fscanf(fp, "%*s %" STR(MAX_PATH) "s %99s %*s %*d %*d\n", mount_point, type) == 2) {
| ^
Increase mount_point variable size to MAX_PATH+1 to avoid the overflow.
Link: https://lkml.kernel.org/r/1b46712e93a2f4153909514a36016959dcc4021c.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Donald Zickus <dzickus@redhat.com>
Fixes: a957cbc02531 ("rtla: Add -C cgroup support")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14f08c976ffe0d2117c6199c32663df1cbc45c65 upstream.
Since the sched_priority for SCHED_OTHER is always 0, it makes no
sence to set it.
Setting nice for SCHED_OTHER seems more meaningful.
Link: https://lkml.kernel.org/r/20240207065142.1753909-1-limingming3@lixiang.com
Cc: stable@vger.kernel.org
Fixes: b1696371d865 ("rtla: Helper functions for rtla")
Signed-off-by: limingming3 <limingming3@lixiang.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 084ce16df0f060efd371092a09a7ae74a536dc11 upstream.
Clang is reporting:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[...]
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions -fstack-protector-strong -fasynchronous-unwind-tables -fstack-clash-protection -Wall -Werror=format-security -Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS $(pkg-config --cflags libtracefs) -c -o src/utils.o src/utils.c
src/utils.c:241:19: warning: unused function 'sched_getattr' [-Wunused-function]
241 | static inline int sched_getattr(pid_t pid, struct sched_attr *attr,
| ^~~~~~~~~~~~~
1 warning generated.
Which is correct, so remove the unused function.
Link: https://lkml.kernel.org/r/eaed7ba122c4ae88ce71277c824ef41cbf789385.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Donald Zickus <dzickus@redhat.com>
Fixes: b1696371d865 ("rtla: Helper functions for rtla")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f9b2c87105c989a7b259c6da87673ada96dce2f8 upstream.
The following errors are showing up when compiling rv with clang:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
[...]
clang -O -g -DVERSION=\"6.8.0-rc1\" -flto=auto -ffat-lto-objects
-fexceptions -fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
-Wno-maybe-uninitialized $(pkg-config --cflags libtracefs)
-I include -c -o src/utils.o src/utils.c
clang: warning: optimization flag '-ffat-lto-objects' is not supported [-Wignored-optimization-argument]
warning: unknown warning option '-Wno-maybe-uninitialized'; did you mean '-Wno-uninitialized'? [-Wunknown-warning-option]
1 warning generated.
clang -o rv -ggdb src/in_kernel.o src/rv.o src/trace.o src/utils.o $(pkg-config --libs libtracefs)
src/in_kernel.o: file not recognized: file format not recognized
clang: error: linker command failed with exit code 1 (use -v to see invocation)
make: *** [Makefile:110: rv] Error 1
Solve these issues by:
- removing -ffat-lto-objects and -Wno-maybe-uninitialized if using clang
- informing the linker about -flto=auto
Link: https://lkml.kernel.org/r/ed94a8ddc2ca8c8ef663cfb7ae9dd196c4a66b33.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Fixes: 4bc4b131d44c ("rv: Add rv tool")
Suggested-by: Donald Zickus <dzickus@redhat.com>
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61ec586bc0815959d3314cf7ce242529c977b357 upstream.
clang is reporting:
$ make HOSTCC=clang CC=clang LLVM_IAS=1
clang -O -g -DVERSION=\"6.8.0-rc3\" -flto=auto -fexceptions
-fstack-protector-strong -fasynchronous-unwind-tables
-fstack-clash-protection -Wall -Werror=format-security
-Wp,-D_FORTIFY_SOURCE=2 -Wp,-D_GLIBCXX_ASSERTIONS
$(pkg-config --cflags libtracefs) -I include
-c -o src/in_kernel.o src/in_kernel.c
[...]
src/in_kernel.c:227:6: warning: variable 'curr_reactor' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
227 | if (!end)
| ^~~~
src/in_kernel.c:242:9: note: uninitialized use occurs here
242 | return curr_reactor;
| ^~~~~~~~~~~~
src/in_kernel.c:227:2: note: remove the 'if' if its condition is always false
227 | if (!end)
| ^~~~~~~~~
228 | goto out_free;
| ~~~~~~~~~~~~~
src/in_kernel.c:221:6: warning: variable 'curr_reactor' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
221 | if (!start)
| ^~~~~~
src/in_kernel.c:242:9: note: uninitialized use occurs here
242 | return curr_reactor;
| ^~~~~~~~~~~~
src/in_kernel.c:221:2: note: remove the 'if' if its condition is always false
221 | if (!start)
| ^~~~~~~~~~~
222 | goto out_free;
| ~~~~~~~~~~~~~
src/in_kernel.c:215:20: note: initialize the variable 'curr_reactor' to silence this warning
215 | char *curr_reactor;
| ^
| = NULL
2 warnings generated.
Which is correct. Setting curr_reactor to NULL avoids the problem.
Link: https://lkml.kernel.org/r/3a35551149e5ee0cb0950035afcb8082c3b5d05b.1707217097.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Bill Wendling <morbo@google.com>
Cc: Justin Stitt <justinstitt@google.com>
Cc: Donald Zickus <dzickus@redhat.com>
Fixes: 6d60f89691fc ("tools/rv: Add in-kernel monitor interface")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 610010737f74482a61896596a0116876ecf9e65c upstream.
The laptop requires a quirk ID to enable its internal microphone. Add
it to the DMI quirk table.
Reported-by: Stanislav Petrov <stanislav.i.petrov@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216925
Cc: stable@vger.kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240205214853.2689-1-mario.limonciello@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 34a1066981a967eab619938e7b35a9be6b4c34e1 upstream.
The tascodec_init() of the snd-soc-tas2781-comlib module is called from
snd-soc-tas2781-i2c and snd-hda-scodec-tas2781-i2c modules. It calls
request_firmware_nowait() with parameter THIS_MODULE and a cont/callback
from the latter modules.
The latter modules can be removed while their callbacks are running,
resulting in a general protection failure.
Add module parameter to tascodec_init() so request_firmware_nowait() can
be called with the module of the callback.
Fixes: ef3bcde75d06 ("ASoC: tas2781: Add tas2781 driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/118dad922cef50525e5aab09badef2fa0eb796e5.1707076603.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fcbe4873089c84da641df75cda9cac2e9addbb4b upstream.
commit 74ad8ed65121 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
introduced a new allocation before the upper bounds check in
do_rx_work. As a result A DSP can cause bad allocations if spewing
garbage.
Fixes: 74ad8ed65121 ("ASoC: SOF: ipc3: Implement rx_msg IPC ops")
Reported-by: Tim Van Patten <timvp@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://msgid.link/r/20240213123834.4827-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fb091ff394792c018527b3211bbdfae93ea4ac02 upstream.
Add the MIDR value of Microsoft Azure Cobalt 100, which is a Microsoft
implemented CPU based on r0p0 of the ARM Neoverse N2 CPU, and therefore
suffers from all the same errata.
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Link: https://lore.kernel.org/r/20240214175522.2457857-1-eahariha@linux.microsoft.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 61da7c8e2a602f66be578cbbcebe8638c10e0f48 upstream.
When we are in a syscall we will only save the FPSIMD subset even though
the task still has access to the full register set, and on context switch
we will only remove TIF_SVE when loading the register state. This means
that the signal handling code should not assume that TIF_SVE means that
the register state is stored in SVE format, it should instead check the
format that was recorded during save.
Fixes: 8c845e273104 ("arm64/sve: Leave SVE enabled on syscall if we don't context switch")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240130-arm64-sve-signal-regs-v2-1-9fc6f9502782@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
by BIOS
commit 58aeb5623c2ebdadefe6352b14f8076a7073fea0 upstream.
Driver shall switch clock source from DLL clock to
OPE clock when power off card to ensure that card
can be identified with OPE clock by BIOS.
Signed-off-by: Fred Ai <fred.ai@bayhubtech.com>
Fixes:4be33cf18703 ("mmc: sdhci-pci-o2micro: Improve card input timing at SDR104/HS200 mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240203102908.4683-1-fredaibayhubtech@126.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 14db5f64a971fce3d8ea35de4dfc7f443a3efb92 upstream.
Write error handling is racy and can sometime lead to the error recovery
path wrongly changing the inode size of a sequential zone file to an
incorrect value which results in garbage data being readable at the end
of a file. There are 2 problems:
1) zonefs_file_dio_write() updates a zone file write pointer offset
after issuing a direct IO with iomap_dio_rw(). This update is done
only if the IO succeed for synchronous direct writes. However, for
asynchronous direct writes, the update is done without waiting for
the IO completion so that the next asynchronous IO can be
immediately issued. However, if an asynchronous IO completes with a
failure right before the i_truncate_mutex lock protecting the update,
the update may change the value of the inode write pointer offset
that was corrected by the error path (zonefs_io_error() function).
2) zonefs_io_error() is called when a read or write error occurs. This
function executes a report zone operation using the callback function
zonefs_io_error_cb(), which does all the error recovery handling
based on the current zone condition, write pointer position and
according to the mount options being used. However, depending on the
zoned device being used, a report zone callback may be executed in a
context that is different from the context of __zonefs_io_error(). As
a result, zonefs_io_error_cb() may be executed without the inode
truncate mutex lock held, which can lead to invalid error processing.
Fix both problems as follows:
- Problem 1: Perform the inode write pointer offset update before a
direct write is issued with iomap_dio_rw(). This is safe to do as
partial direct writes are not supported (IOMAP_DIO_PARTIAL is not
set) and any failed IO will trigger the execution of zonefs_io_error()
which will correct the inode write pointer offset to reflect the
current state of the one on the device.
- Problem 2: Change zonefs_io_error_cb() into zonefs_handle_io_error()
and call this function directly from __zonefs_io_error() after
obtaining the zone information using blkdev_report_zones() with a
simple callback function that copies to a local stack variable the
struct blk_zone obtained from the device. This ensures that error
handling is performed holding the inode truncate mutex.
This change also simplifies error handling for conventional zone files
by bypassing the execution of report zones entirely. This is safe to
do because the condition of conventional zones cannot be read-only or
offline and conventional zone files are always fully mapped with a
constant file size.
Reported-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 8dcc1a9d90c1 ("fs: New zonefs file system")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 10c02aad111df02088d1a81792a709f6a7eca6cc upstream.
The rule inside kvm enforces that the vcpu->mutex is taken *inside*
kvm->lock. The rule is violated by the pkvm_create_hyp_vm() which acquires
the kvm->lock while already holding the vcpu->mutex lock from
kvm_vcpu_ioctl(). Avoid the circular locking dependency altogether by
protecting the hyp vm handle with the config_lock, much like we already
do for other forms of VM-scoped data.
Signed-off-by: Sebastian Ene <sebastianene@google.com>
Cc: stable@vger.kernel.org
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240124091027.1477174-2-sebastianene@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe752331d4b361d43cfd0b89534b4b2176057c32 upstream.
Right now it is possible to see gmap->private being zero in
kvm_s390_vsie_gmap_notifier resulting in a crash. This is due to the
fact that we add gmap->private == kvm after creation:
static int acquire_gmap_shadow(struct kvm_vcpu *vcpu,
struct vsie_page *vsie_page)
{
[...]
gmap = gmap_shadow(vcpu->arch.gmap, asce, edat);
if (IS_ERR(gmap))
return PTR_ERR(gmap);
gmap->private = vcpu->kvm;
Let children inherit the private field of the parent.
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Fixes: a3508fbe9dc6 ("KVM: s390: vsie: initial support for nested virtualization")
Cc: <stable@vger.kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Link: https://lore.kernel.org/r/20231220125317.4258-1-borntraeger@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4860abb91f3d7fbaf8147d54782149bb1fc45892 upstream.
The conversion to netfs in the 6.3 kernel caused a regression when
maximum write size is set by the server to an unexpected value which is
not a multiple of 4096 (similarly if the user overrides the maximum
write size by setting mount parm "wsize", but sets it to a value that
is not a multiple of 4096). When negotiated write size is not a
multiple of 4096 the netfs code can skip the end of the final
page when doing large sequential writes, causing data corruption.
This section of code is being rewritten/removed due to a large
netfs change, but until that point (ie for the 6.3 kernel until now)
we can not support non-standard maximum write sizes.
Add a warning if a user specifies a wsize on mount that is not
a multiple of 4096 (and round down), also add a change where we
round down the maximum write size if the server negotiates a value
that is not a multiple of 4096 (we also have to check to make sure that
we do not round it down to zero).
Reported-by: "R. Diez" <rdiez-2006@rd10.de>
Fixes: d08089f649a0 ("cifs: Change the I/O paths to use an iterator rather than a page list")
Suggested-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Acked-by: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Tested-by: Matthew Ruffell <matthew.ruffell@canonical.com>
Reviewed-by: Shyam Prasad N <sprasad@microsoft.com>
Cc: stable@vger.kernel.org # v6.3+
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4508ec17357094e2075f334948393ddedbb75157 upstream.
When uid, gid and cruid are not specified, we need to dynamically
set them into the filesystem context used for automounting otherwise
they'll end up reusing the values from the parent mount.
Fixes: 9fd29a5bae6e ("cifs: use fs_context for automounts")
Reported-by: Shane Nehring <snehring@iastate.edu>
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2259257
Cc: stable@vger.kernel.org # 6.2+
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ec4d82f855ce332de26fe080892483de98cc1a19 upstream.
The bit 23, CM TBT3 Not Supported (CNS), in ROUTER_CS_5 indicates
whether a USB4 Connection Manager is TBT3-Compatible and should be:
0b for TBT3-Compatible
1b for Not TBT3-Compatible
Fixes: b04079837b20 ("thunderbolt: Add initial support for USB4")
Cc: stable@vger.kernel.org
Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit af9acbfc2c4b72c378d0b9a2ee023ed01055d3e2 upstream.
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a216e (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP)
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8b02da04ad978827e5ccd675acf170198f747a7a upstream.
While refactoring the way the ITSs are probed, the handling of quirks
applicable to ACPI-based platforms was lost. As a result, systems such as
HIP07 lose their GICv4 functionnality, and some other may even fail to
boot, unless they are configured to boot with DT.
Move the enabling of quirks into its_probe_one(), making it common to all
firmware implementations.
Fixes: 9585a495ac93 ("irqchip/gic-v3-its: Split allocation from initialisation of its_node")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240213101206.2137483-3-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b0344d6854d25a8b3b901c778b1728885dd99007 upstream.
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e92766e ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b5d1b4b46f856da1473c7ba9a5cdfcb55c9b2478 upstream.
The "msg_addr" variable is u64. However, the "aligned_offset" is an
unsigned int. This means that when the code does:
msg_addr &= ~aligned_offset;
it will unintentionally zero out the high 32 bits. Use ALIGN_DOWN() to do
the alignment instead.
Fixes: 2217fffcd63f ("PCI: dwc: endpoint: Fix dw_pcie_ep_raise_msix_irq() alignment support")
Link: https://lore.kernel.org/r/af59c7ad-ab93-40f7-ad4a-7ac0b14d37f5@moroto.mountain
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b7198383ef2debe748118996f627452281cf27d7 upstream.
A DoS tool that injects loads of authentication frames made our AP
crash. The iwl_mvm_is_dup() function couldn't find the per-queue
dup_data which was not allocated.
The root cause for that is that we ran out of stations in the firmware
and we didn't really add the station to the firmware, yet we didn't
return an error to mac80211.
Mac80211 was thinking that we have the station and because of that,
sta_info::uploaded was set to 1. This allowed
ieee80211_find_sta_by_ifaddr() to return a valid station object, but
that ieee80211_sta didn't have any iwl_mvm_sta object initialized and
that caused the crash mentioned earlier when we got Rx on that station.
Cc: stable@vger.kernel.org
Fixes: 57974a55d995 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240206175739.1f76c44b2486.I6a00955e2842f15f0a089db2f834adb9d10fbe35@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c98d8836b817d11fdff4ca7749cbbe04ff7f0c64 upstream.
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
Cc: stable@vger.kernel.org
Fixes: 531682159092 ("mac80211: fix VLAN handling with TXQs")
Link: https://msgid.link/20240131164910.b54c28d583bc.I29450cec84ea6773cff5d9c16ff92b836c331471@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
