| Age | Commit message (Collapse) | Author |
|---|
|
commit d72cca1eee5b26e313da2a380d4862924e271031 upstream.
One of the side effects of deferred probe is that some drivers which
used to be probed before initcalls completed are now happening slightly
later. This causes two problems.
- If a console driver gets deferred, then it may not be ready when
userspace starts. For example, if a uart depends on pinctrl, then the
uart will get deferred and /dev/console will not be available
- __init sections will be discarded before built-in drivers are probed.
Strictly speaking, __init functions should not be called in a drivers
__probe path, but there are a lot of drivers (console stuff again)
that do anyway. In the past it was perfectly safe to do so because all
built-in drivers got probed before the end of initcalls.
This patch fixes the problem by forcing the first pass of the deferred
list to complete at late_initcall time. This is late enough to catch the
drivers that are known to have the above issues.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pages
commit 67d46b296a1ba1477c0df8ff3bc5e0167a0b0732 upstream.
Rob van der Heij reported the following (paraphrased) on private mail.
The scenario is that I want to avoid backups to fill up the page
cache and purge stuff that is more likely to be used again (this is
with s390x Linux on z/VM, so I don't give it as much memory that
we don't care anymore). So I have something with LD_PRELOAD that
intercepts the close() call (from tar, in this case) and issues
a posix_fadvise() just before closing the file.
This mostly works, except for small files (less than 14 pages)
that remains in page cache after the face.
Unfortunately Rob has not had a chance to test this exact patch but the
test program below should be reproducing the problem he described.
The issue is the per-cpu pagevecs for LRU additions. If the pages are
added by one CPU but fadvise() is called on another then the pages
remain resident as the invalidate_mapping_pages() only drains the local
pagevecs via its call to pagevec_release(). The user-visible effect is
that a program that uses fadvise() properly is not obeyed.
A possible fix for this is to put the necessary smarts into
invalidate_mapping_pages() to globally drain the LRU pagevecs if a
pagevec page could not be discarded. The downside with this is that an
inode cache shrink would send a global IPI and memory pressure
potentially causing global IPI storms is very undesirable.
Instead, this patch adds a check during fadvise(POSIX_FADV_DONTNEED) to
check if invalidate_mapping_pages() discarded all the requested pages.
If a subset of pages are discarded it drains the LRU pagevecs and tries
again. If the second attempt fails, it assumes it is due to the pages
being mapped, locked or dirty and does not care. With this patch, an
application using fadvise() correctly will be obeyed but there is a
downside that a malicious application can force the kernel to send
global IPIs and increase overhead.
If accepted, I would like this to be considered as a -stable candidate.
It's not an urgent issue but it's a system call that is not working as
advertised which is weak.
The following test program demonstrates the problem. It should never
report that pages are still resident but will without this patch. It
assumes that CPU 0 and 1 exist.
int main() {
int fd;
int pagesize = getpagesize();
ssize_t written = 0, expected;
char *buf;
unsigned char *vec;
int resident, i;
cpu_set_t set;
/* Prepare a buffer for writing */
expected = FILESIZE_PAGES * pagesize;
buf = malloc(expected + 1);
if (buf == NULL) {
printf("ENOMEM\n");
exit(EXIT_FAILURE);
}
buf[expected] = 0;
memset(buf, 'a', expected);
/* Prepare the mincore vec */
vec = malloc(FILESIZE_PAGES);
if (vec == NULL) {
printf("ENOMEM\n");
exit(EXIT_FAILURE);
}
/* Bind ourselves to CPU 0 */
CPU_ZERO(&set);
CPU_SET(0, &set);
if (sched_setaffinity(getpid(), sizeof(set), &set) == -1) {
perror("sched_setaffinity");
exit(EXIT_FAILURE);
}
/* open file, unlink and write buffer */
fd = open("fadvise-test-file", O_CREAT|O_EXCL|O_RDWR);
if (fd == -1) {
perror("open");
exit(EXIT_FAILURE);
}
unlink("fadvise-test-file");
while (written < expected) {
ssize_t this_write;
this_write = write(fd, buf + written, expected - written);
if (this_write == -1) {
perror("write");
exit(EXIT_FAILURE);
}
written += this_write;
}
free(buf);
/*
* Force ourselves to another CPU. If fadvise only flushes the local
* CPUs pagevecs then the fadvise will fail to discard all file pages
*/
CPU_ZERO(&set);
CPU_SET(1, &set);
if (sched_setaffinity(getpid(), sizeof(set), &set) == -1) {
perror("sched_setaffinity");
exit(EXIT_FAILURE);
}
/* sync and fadvise to discard the page cache */
fsync(fd);
if (posix_fadvise(fd, 0, expected, POSIX_FADV_DONTNEED) == -1) {
perror("posix_fadvise");
exit(EXIT_FAILURE);
}
/* map the file and use mincore to see which parts of it are resident */
buf = mmap(NULL, expected, PROT_READ, MAP_SHARED, fd, 0);
if (buf == NULL) {
perror("mmap");
exit(EXIT_FAILURE);
}
if (mincore(buf, expected, vec) == -1) {
perror("mincore");
exit(EXIT_FAILURE);
}
/* Check residency */
for (i = 0, resident = 0; i < FILESIZE_PAGES; i++) {
if (vec[i])
resident++;
}
if (resident != 0) {
printf("Nr unexpected pages resident: %d\n", resident);
exit(EXIT_FAILURE);
}
munmap(buf, expected);
close(fd);
free(vec);
exit(EXIT_SUCCESS);
}
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Rob van der Heij <rvdheij@gmail.com>
Tested-by: Rob van der Heij <rvdheij@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5f00110f7273f9ff04ac69a5f85bb535a4fd0987 upstream.
The tmpfs remount logic preserves filesystem mempolicy if the mpol=M
option is not specified in the remount request. A new policy can be
specified if mpol=M is given.
Before this patch remounting an mpol bound tmpfs without specifying
mpol= mount option in the remount request would set the filesystem's
mempolicy object to a freed mempolicy object.
To reproduce the problem boot a DEBUG_PAGEALLOC kernel and run:
# mkdir /tmp/x
# mount -t tmpfs -o size=100M,mpol=interleave nodev /tmp/x
# grep /tmp/x /proc/mounts
nodev /tmp/x tmpfs rw,relatime,size=102400k,mpol=interleave:0-3 0 0
# mount -o remount,size=200M nodev /tmp/x
# grep /tmp/x /proc/mounts
nodev /tmp/x tmpfs rw,relatime,size=204800k,mpol=??? 0 0
# note ? garbage in mpol=... output above
# dd if=/dev/zero of=/tmp/x/f count=1
# panic here
Panic:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [< (null)>] (null)
[...]
Oops: 0010 [#1] SMP DEBUG_PAGEALLOC
Call Trace:
mpol_shared_policy_init+0xa5/0x160
shmem_get_inode+0x209/0x270
shmem_mknod+0x3e/0xf0
shmem_create+0x18/0x20
vfs_create+0xb5/0x130
do_last+0x9a1/0xea0
path_openat+0xb3/0x4d0
do_filp_open+0x42/0xa0
do_sys_open+0xfe/0x1e0
compat_sys_open+0x1b/0x20
cstar_dispatch+0x7/0x1f
Non-debug kernels will not crash immediately because referencing the
dangling mpol will not cause a fault. Instead the filesystem will
reference a freed mempolicy object, which will cause unpredictable
behavior.
The problem boils down to a dropped mpol reference below if
shmem_parse_options() does not allocate a new mpol:
config = *sbinfo
shmem_parse_options(data, &config, true)
mpol_put(sbinfo->mpol)
sbinfo->mpol = config.mpol /* BUG: saves unreferenced mpol */
This patch avoids the crash by not releasing the mempolicy if
shmem_parse_options() doesn't create a new mpol.
How far back does this issue go? I see it in both 2.6.36 and 3.3. I did
not look back further.
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5eb02c01bd1f3ef195989ab05e835e2b0711b5a9 upstream.
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3278bb748d2437eb1464765f36429e5d6aa91c38 upstream.
If lockres refresh failed, the super lock will never be released which
will cause some processes on other cluster nodes hung forever.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7630b661da330b35dd57b6f5d6d62b386f2dd751 upstream.
We found that bdev->bd_invalidated was left set once revalidate_disk()
is called, which results in page cache flush every time that device is
open.
Specifically, we found this problem in MD block device. Once we resize
a MD device, mdadm --monitor periodically flush all page cache for that
device every 60 or 1000 seconds when it opens the device.
This bug lies since at least 3.2.0 till the latest kernel(3.6.2). Patch
is attached.
The following steps will reproduce the problem.
1. prepair a block device (eg /dev/sdb).
2. create two partitions:
sudo parted /dev/sdb
mklabel gpt
mkpart primary 0% 50%
mkpart primary 50% 100%
3. create a md device.
sudo mdadm -C /dev/md/hoge -l 1 -n 2 -e 1.2 --assume-clean --auto=md --symlink=no /dev/sdb1 /dev/sdb2
4. create file system and mount it
sudo mkfs.ext3 /dev/md/hoge
sudo mkdir /mnt/test
sudo mount /dev/md/hoge /mnt/test
5. try to resize the device
sudo mdadm -G /dev/md/hoge --size=max
6. create a file to fill file cache.
sudo dd if=/dev/urandom of=/mnt/test/data bs=1M count=10
and verify the current status of file by free command.
7. mdadm monitor will open the md device every 1000 seconds and you
will find all file cache on the device are cleared.
The timing can be reduced by the following steps.
a) kill mdadm and restart it with --delay option
/sbin/mdadm --monitor --delay=30 --pid-file /var/run/mdadm/monitor.pid --daemonise --scan --syslog
or open the md device directly.
sudo dd if=/dev/md/hoge of=/dev/null bs=4096 count=1
Signed-off-by: MITSUNARI Shigeo <herumi@nifty.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 676a0675cf9200ac047fb50825f80867b3bb733b upstream.
Running the command:
inotifywait -e unmount /mnt/disk
immediately aborts with a -EINVAL return code. This is however a valid
parameter. This abort occurs only if unmount is the sole event
parameter. If other event parameters are supplied, then the unmount
event wait will work.
The problem was introduced by commit 44b350fc23e ("inotify: Fix mask
checks"). In that commit, it states:
The mask checks in inotify_update_existing_watch() and
inotify_new_watch() are useless because inotify_arg_to_mask()
sets FS_IN_IGNORED and FS_EVENT_ON_CHILD bits anyway.
But instead of removing the useless checks, it did this:
mask = inotify_arg_to_mask(arg);
- if (unlikely(!mask))
+ if (unlikely(!(mask & IN_ALL_EVENTS)))
return -EINVAL;
The problem is that IN_ALL_EVENTS doesn't include IN_UNMOUNT, and other
parts of the code keep IN_UNMOUNT separate from IN_ALL_EVENTS. So the
check should be:
if (unlikely(!(mask & (IN_ALL_EVENTS | IN_UNMOUNT))))
But inotify_arg_to_mask(arg) always sets the IN_UNMOUNT bit in the mask
anyway, so the check is always going to pass and thus should simply be
removed. Also note that inotify_arg_to_mask completely controls what
mask bits get set from arg, there's no way for invalid bits to get
enabled there.
Lets fix it by simply removing the useless broken checks.
Signed-off-by: Jim Somerville <Jim.Somerville@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: John McCutchan <john@johnmccutchan.com>
Cc: Robert Love <rlove@rlove.org>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fe2b05f7ca9f906be61dced5489f63b8b4d7c770 upstream.
This reverts commit ec0c4274e33c0373e476b73e01995c53128f1257.
get_robust_list() is in use and a removal would break existing user
space. With the permission checks in place it's not longer a security
hole. Remove the deprecation warnings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: akpm@linux-foundation.org
Cc: paul.gortmaker@windriver.com
Cc: davej@redhat.com
Cc: keescook@chromium.org
Cc: ebiederm@xmission.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 15bc8d8457875f495c59d933b05770ba88d1eacb upstream.
On store status we need to copy the current state of registers
into a save area. Currently we might save stale versions:
The sie state descriptor doesnt have fields for guest ACRS,FPRS,
those registers are simply stored in the host registers. The host
program must copy these away if needed. We do that in vcpu_put/load.
If we now do a store status in KVM code between vcpu_put/load, the
saved values are not up-to-date. Lets collect the ACRS/FPRS before
saving them.
This also fixes some strange problems with hotplug and virtio-ccw,
since the low level machine check handler (on hotplug a machine check
will happen) will revalidate all registers with the content of the
save area.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 55c171a6d90dc0574021f9c836127cfd1a7d2e30 upstream.
Running under a kvm host does not necessarily imply the presence of
a page mapped above the main memory with the virtio information;
however, the code includes a hard coded access to that page.
Instead, check for the presence of the page and exit gracefully
before we hit an addressing exception if it does not exist.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 751efd8610d3d7d67b7bdf7f62646edea7365dd7 upstream.
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result of a
filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
Additionally, the list traversal in __mmu_notifier_release() is not
protected by the by the mmu_notifier_mm->hlist_lock which can result in
callouts to the ->release() notifier from both mmu_notifier_unregister()
and __mmu_notifier_release().
-stable suggestions:
The stable trees prior to 3.7.y need commits 21a92735f660 and
70400303ce0c cherry-picked in that order prior to cherry-picking this
commit. The 3.7.y tree already has those two commits.
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.co.il>
Cc: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 70400303ce0c4ced3139499c676d5c79636b0c72 upstream.
The variable must be static especially given the variable name.
s/RCU/SRCU/ over a few comments.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
schedule
commit 21a92735f660eaecf69a6f2e777f18463760ec32 upstream.
With an RCU based mmu_notifier implementation, any callout to
mmu_notifier_invalidate_range_{start,end}() or
mmu_notifier_invalidate_page() would not be allowed to call schedule()
as that could potentially allow a modification to the mmu_notifier
structure while it is currently being used.
Since srcu allocs 4 machine words per instance per cpu, we may end up
with memory exhaustion if we use srcu per mm. So all mms share a global
srcu. Note that during large mmu_notifier activity exit & unregister
paths might hang for longer periods, but it is tolerable for current
mmu_notifier clients.
Signed-off-by: Sagi Grimberg <sagig@mellanox.co.il>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Haggai Eran <haggaie@mellanox.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4fa3e78be7e985ca814ce2aa0c09cbee404efcf7 upstream.
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Reported-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e7e44e444876478d50630f57b0c31d29f6725020 upstream.
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 76eaca031f0af2bb303e405986f637811956a422 upstream.
There is a loophole between Xen's current implementation of
pv-spinlocks and the scheduler. This was triggerable through
a testcase until v3.6 changed the TLB flushing code. The
problem potentially is still there just not observable in the
same way.
What could happen was (is):
1. CPU n tries to schedule task x away and goes into a slow
wait for the runq lock of CPU n-# (must be one with a lower
number).
2. CPU n-#, while processing softirqs, tries to balance domains
and goes into a slow wait for its own runq lock (for updating
some records). Since this is a spin_lock_irqsave in softirq
context, interrupts will be re-enabled for the duration of
the poll_irq hypercall used by Xen.
3. Before the runq lock of CPU n-# is unlocked, CPU n-1 receives
an interrupt (e.g. endio) and when processing the interrupt,
tries to wake up task x. But that is in schedule and still
on_cpu, so try_to_wake_up goes into a tight loop.
4. The runq lock of CPU n-# gets unlocked, but the message only
gets sent to the first waiter, which is CPU n-# and that is
busily stuck.
5. CPU n-# never returns from the nested interruption to take and
release the lock because the scheduler uses a busy wait.
And CPU n never finishes the task migration because the unlock
notification only went to CPU n-#.
To avoid this and since the unlocking code has no real sense of
which waiter is best suited to grab the lock, just send the IPI
to all of them. This causes the waiters to return from the hyper-
call (those not interrupted at least) and do active spinlocking.
BugLink: http://bugs.launchpad.net/bugs/1011792
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
separately
commit bc6b89237acb3dee6af6e64e51a18255fef89cc2 upstream.
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8708aac79e4572ba673d7a21e94ddca9f3abb7fc upstream.
A new model of the RTL8188CUS has appeared.
Reported-and-tested-by: Thomas Rosenkrantz <tom.rosary@googlemail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ccae0e50c16a7f7adb029c169147400d1ce9f703 upstream.
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bastian Bittorf <bittorf@bluebottle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b2ca699076573c94fee9a73cb0d8645383b602a0 upstream.
Make sure serial-driver dtr_rts is called with disc_mutex held after
checking the disconnected flag.
Due to a bug in the tty layer, dtr_rts may get called after a device has
been disconnected and the tty-device unregistered. Some drivers have had
individual checks for disconnect to make sure the disconnected interface
was not accessed, but this should really be handled in usb-serial core
(at least until the long-standing tty-bug has been fixed).
Note that the problem has been made more acute with commit 0998d0631001
("device-core: Ensure drvdata = NULL when no driver is bound") as the
port data is now also NULL when dtr_rts is called resulting in further
oopses.
Reported-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 183d95cdd834381c594d3aa801c1f9f9c0c54fa9 upstream.
See https://bugzilla.redhat.com/show_bug.cgi?id=904907
read command causes bash to abort with double free or corruption (out).
A simple test-case from Roman:
// Compile the reproducer and send sigchld ti that process.
// EINTR occurs even if SA_RESTART flag is set.
void handler(int sig)
{
}
main()
{
struct sigaction act;
act.sa_handler = handler;
act.sa_flags = SA_RESTART;
sigaction (SIGCHLD, &act, 0);
struct termio ttp;
ioctl(0, TCGETA, &ttp);
while(1)
{
if (ioctl(0, TCSETAW, ttp) < 0)
{
if (errno == EINTR)
{
fprintf(stderr, "BUG!"); return(1);
}
}
}
}
Change set_termios/set_termiox to return -ERESTARTSYS to fix this
particular problem.
I didn't dare to change other EINTR's in drivers/tty/, but they look
equally wrong.
Reported-by: Roman Rakus <rrakus@redhat.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d9b109060f690f5c835130ff54165ae157b3087 upstream.
This change fixes a deadlock when the multiplexer is closed while there
are still client side ports open.
When the multiplexer is closed and there are active tty's it tries to
close them with tty_vhangup. This has a problem though, because
tty_vhangup needs the tty_lock. This patch changes it to unlock the
tty_lock before attempting the hangup and relocks afterwards. The
additional call to tty_port_tty_set is needed because otherwise the
port stays active because of the reference counter.
This change also exposed another problem that other code paths don't
expect that the multiplexer could have been closed. This patch also adds
checks for these cases in the gsmtty_ class of function that could be
called.
The documentation explicitly states that "first close all virtual ports
before closing the physical port" but we've found this to not always
reality in our field situations. The GPRS / UTMS modem sometimes crashes
and needs a power cycle in that case which means cleanly shutting down
everything is not always possible. This change makes it much more robust
for our situation where at least the system is recoverable with this patch
and doesn't hang in a deadlock situation inside the kernel.
The patch is against the long term support kernel (3.4.27) and should
apply cleanly to more recent branches. Tested with a Telit GE864-QUADV2
and Telit HE910 modem.
Signed-off-by: Dirkjan Bussink <dirkjan.bussink@nedap.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f49a59c4471d81a233e09dda45187cc44fda009d upstream.
According to the other code in this driver and similar
code in rme96 it seems, that spin_lock_irq in
snd_rme32_capture_close function should be paired
with spin_unlock_irq.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dacae5a19b4cbe1b5e3a86de23ea74cbe9ec9652 upstream.
snd_ali_pointer function is called with local
interrupts disabled. However it seems very strange to
reenable them in such way.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 32068f6527b8f1822a30671dedaf59c567325026 upstream.
Enable hyperv_clocksource only if its advertised as a feature.
XenServer 6 returns the signature which is checked in
ms_hyperv_platform(), but it does not offer all features. Currently the
clocksource is enabled unconditionally in ms_hyperv_init_platform(), and
the result is a hanging guest.
Hyper-V spec Bit 1 indicates the availability of Partition Reference
Counter. Register the clocksource only if this bit is set.
The guest in question prints this in dmesg:
[ 0.000000] Hypervisor detected: Microsoft HyperV
[ 0.000000] HyperV: features 0x70, hints 0x0
This bug can be reproduced easily be setting 'viridian=1' in a HVM domU
.cfg file. A workaround without this patch is to boot the HVM guest with
'clocksource=jiffies'.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Link: http://lkml.kernel.org/r/1359940959-32168-1-git-send-email-kys@microsoft.com
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b22affe0aef429d657bc6505aacb1c569340ddd2 upstream.
hrtimer_enqueue_reprogram contains a race which could result in
timer.base switch during unlock/lock sequence.
hrtimer_enqueue_reprogram is releasing the lock protecting the timer
base for calling raise_softirq_irqsoff() due to a lock ordering issue
versus rq->lock.
If during that time another CPU calls __hrtimer_start_range_ns() on
the same hrtimer, the timer base might switch, before the current CPU
can lock base->lock again and therefor the unlock_timer_base() call
will unlock the wrong lock.
[ tglx: Added comment and massaged changelog ]
Signed-off-by: Leonid Shatz <leonid.shatz@ravellosystems.com>
Signed-off-by: Izik Eidus <izik.eidus@ravellosystems.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Link: http://lkml.kernel.org/r/1359981217-389-1-git-send-email-izik.eidus@ravellosystems.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6c42c295e071dd74a66b5a9fcf4f44049888ed8 upstream.
The trinity fuzzer triggered a task_struct reference leak via
clock_nanosleep with CPU_TIMERs. do_cpu_nanosleep() calls
posic_cpu_timer_create(), but misses a corresponding
posix_cpu_timer_del() which leads to the task_struct reference leak.
Reported-and-tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20130215100810.GF4392@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e716efde75267eab919cdb2bef5b2cb77f305326 upstream.
commit 52553ddf(genirq: fix regression in irqfixup, irqpoll)
introduced a potential deadlock by calling the action handler with the
irq descriptor lock held.
Remove the call and let the handling code run even for an interrupt
where only a single action is registered. That matches the goal of
the above commit and avoids the deadlock.
Document the confusing action = desc->action reload in the handling
loop while at it.
Reported-and-tested-by: "Wang, Warner" <warner.wang@hp.com>
Tested-by: Edward Donovan <edward.donovan@numble.net>
Cc: "Wang, Song-Bo (Stoney)" <song-bo.wang@hp.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 63a3f603413ffe82ad775f2d62a5afff87fd94a0 upstream.
defined(@array) is deprecated in Perl and gives off a warning.
Restructure the code to remove that warning.
[ hpa: it would be interesting to revert to the timeconst.bc script.
It appears that the failures reported by akpm during testing of
that script was due to a known broken version of make, not a problem
with bc. The Makefile rules could probably be restructured to avoid
the make bug, or it is probably old enough that it doesn't matter. ]
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7c45512df987c5619db041b5c9b80d281e26d3db upstream.
Commit c060f943d092 ("mm: use aligned zone start for pfn_to_bitidx
calculation") fixed out calculation of the index into the pageblock
bitmap when a !SPARSEMEM zome was not aligned to pageblock_nr_pages.
However, the _allocation_ of that bitmap had never taken this alignment
requirement into accout, so depending on the exact size and alignment of
the zone, the use of that index could then access past the allocation,
resulting in some very subtle memory corruption.
This was reported (and bisected) by Ingo Molnar: one of his random
config builds would hang with certain very specific kernel command line
options.
In the meantime, commit c060f943d092 has been marked for stable, so this
fix needs to be back-ported to the stable kernels that backported the
commit to use the right alignment.
Bisected-and-tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 07f4207a305c834f528d08428df4531744e25678 upstream.
We have removed the remap allocator for x86-32, and x86-64 never had
it (and doesn't need it). Remove residual reference to it.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/CAE9FiQVn6_QZi3fNQ-JHYiR-7jeDJ5hT0SyT_%2BzVvfOj=PzF3w@mail.gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb112aec5ee41427e9b9726e3d57b896709598ed upstream.
Remove reference to removed function resume_map_numa_kva().
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f03574f2d5b2d6229dcdf2d322848065f72953c7 upstream.
This code was an optimization for 32-bit NUMA systems.
It has probably been the cause of a number of subtle bugs over
the years, although the conditions to excite them would have
been hard to trigger. Essentially, we remap part of the kernel
linear mapping area, and then sometimes part of that area gets
freed back in to the bootmem allocator. If those pages get
used by kernel data structures (say mem_map[] or a dentry),
there's no big deal. But, if anyone ever tried to use the
linear mapping for these pages _and_ cared about their physical
address, bad things happen.
For instance, say you passed __GFP_ZERO to the page allocator
and then happened to get handed one of these pages, it zero the
remapped page, but it would make a pte to the _old_ page.
There are probably a hundred other ways that it could screw
with things.
We don't need to hang on to performance optimizations for
these old boxes any more. All my 32-bit NUMA systems are long
dead and buried, and I probably had access to more than most
people.
This code is causing real things to break today:
https://lkml.org/lkml/2013/1/9/376
I looked in to actually fixing this, but it requires surgery
to way too much brittle code, as well as stuff like
per_cpu_ptr_to_phys().
[ hpa: Cc: this for -stable, since it is a memory corruption issue.
However, an alternative is to simply mark NUMA as depends BROKEN
rather than EXPERIMENTAL in the X86_32 subclause... ]
Link: http://lkml.kernel.org/r/20130131005616.1C79F411@kernel.stglabs.ibm.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
call_console_drivers
This patch corrects a buffer overflow in kernels from 3.0 to 3.4 when calling
log_prefix() function from call_console_drivers().
This bug existed in previous releases but has been revealed with commit
162a7e7500f9664636e649ba59defe541b7c2c60 (2.6.39 => 3.0) that made changes
about how to allocate memory for early printk buffer (use of memblock_alloc).
It disappears with commit 7ff9554bb578ba02166071d2d487b7fc7d860d62 (3.4 => 3.5)
that does a refactoring of printk buffer management.
In log_prefix(), the access to "p[0]", "p[1]", "p[2]" or
"simple_strtoul(&p[1], &endp, 10)" may cause a buffer overflow as this
function is called from call_console_drivers by passing "&LOG_BUF(cur_index)"
where the index must be masked to do not exceed the buffer's boundary.
The trick is to prepare in call_console_drivers() a buffer with the necessary
data (PRI field of syslog message) to be safely evaluated in log_prefix().
This patch can be applied to stable kernel branches 3.0.y, 3.2.y and 3.4.y.
Without this patch, one can freeze a server running this loop from shell :
$ export DUMMY=`cat /dev/urandom | tr -dc '12345AZERTYUIOPQSDFGHJKLMWXCVBNazertyuiopqsdfghjklmwxcvbn' | head -c255`
$ while true do ; echo $DUMMY > /dev/kmsg ; done
The "server freeze" depends on where memblock_alloc does allocate printk buffer :
if the buffer overflow is inside another kernel allocation the problem may not
be revealed, else the server may hangs up.
Signed-off-by: Alexandre SIMON <Alexandre.Simon@univ-lorraine.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit ae1c07a6b7ced6c0c94c99e3b53f4e7856fa8bff upstream.
For some reason the reading of the RQDPC register was being artificially
limited to 4K. Instead of limiting the value we should read the value and
add the full amount. Otherwise this can lead to a misleading number of
dropped packets when the actual value is in fact much higher.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vinson Lee <vlee@twitter.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1de63d60cd5b0d33a812efa455d5933bf1564a51 upstream.
There was a serious problem in samsung-laptop that its platform driver is
designed to run under BIOS and running under EFI can cause the machine to
become bricked or can cause Machine Check Exceptions.
Discussion about this problem:
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
https://bugzilla.kernel.org/show_bug.cgi?id=47121
The patches to fix this problem:
efi: Make 'efi_enabled' a function to query EFI facilities
83e68189745ad931c2afd45d8ee3303929233e7f
samsung-laptop: Disable on EFI hardware
e0094244e41c4d0c7ad69920681972fc45d8ce34
Unfortunately this problem comes back again if users specify "noefi" option.
This parameter clears EFI_BOOT and that driver continues to run even if running
under EFI. Refer to the document, this parameter should clear
EFI_RUNTIME_SERVICES instead.
Documentation/kernel-parameters.txt:
===============================================================================
...
noefi [X86] Disable EFI runtime services support.
...
===============================================================================
Documentation/x86/x86_64/uefi.txt:
===============================================================================
...
- If some or all EFI runtime services don't work, you can try following
kernel command line parameters to turn off some or all EFI runtime
services.
noefi turn off all EFI runtime services
...
===============================================================================
Signed-off-by: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/511C2C04.2070108@jp.fujitsu.com
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 249bfb83cf8ba658955f0245ac3981d941f746ee upstream.
Devices are added to pci_pme_list when drivers use pci_enable_wake()
or pci_wake_from_d3(), but they aren't removed from the list unless
the driver explicitly disables wakeup. Many drivers never disable
wakeup, so their devices remain on the list even after they are
removed, e.g., via hotplug. A subsequent PME poll will oops when
it tries to touch the device.
This patch disables PME# on a device before removing it, which removes
the device from pci_pme_list. This is safe even if the device never
had PME# enabled.
This oops can be triggered by unplugging a Thunderbolt ethernet adapter
on a Macbook Pro, as reported by Daniel below.
[bhelgaas: changelog]
Reference: http://lkml.kernel.org/r/CAMVG2svG21yiM1wkH4_2pen2n+cr2-Zv7TbH3Gj+8MwevZjDbw@mail.gmail.com
Reported-and-tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 13d2b4d11d69a92574a55bfd985cfb0ca77aebdc upstream.
This fixes CVE-2013-0228 / XSA-42
Drew Jones while working on CVE-2013-0190 found that that unprivileged guest user
in 32bit PV guest can use to crash the > guest with the panic like this:
-------------
general protection fault: 0000 [#1] SMP
last sysfs file: /sys/devices/vbd-51712/block/xvda/dev
Modules linked in: sunrpc ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4
iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6
xt_state nf_conntrack ip6table_filter ip6_tables ipv6 xen_netfront ext4
mbcache jbd2 xen_blkfront dm_mirror dm_region_hash dm_log dm_mod [last
unloaded: scsi_wait_scan]
Pid: 1250, comm: r Not tainted 2.6.32-356.el6.i686 #1
EIP: 0061:[<c0407462>] EFLAGS: 00010086 CPU: 0
EIP is at xen_iret+0x12/0x2b
EAX: eb8d0000 EBX: 00000001 ECX: 08049860 EDX: 00000010
ESI: 00000000 EDI: 003d0f00 EBP: b77f8388 ESP: eb8d1fe0
DS: 0000 ES: 007b FS: 0000 GS: 00e0 SS: 0069
Process r (pid: 1250, ti=eb8d0000 task=c2953550 task.ti=eb8d0000)
Stack:
00000000 0027f416 00000073 00000206 b77f8364 0000007b 00000000 00000000
Call Trace:
Code: c3 8b 44 24 18 81 4c 24 38 00 02 00 00 8d 64 24 30 e9 03 00 00 00
8d 76 00 f7 44 24 08 00 00 02 80 75 33 50 b8 00 e0 ff ff 21 e0 <8b> 40
10 8b 04 85 a0 f6 ab c0 8b 80 0c b0 b3 c0 f6 44 24 0d 02
EIP: [<c0407462>] xen_iret+0x12/0x2b SS:ESP 0069:eb8d1fe0
general protection fault: 0000 [#2]
---[ end trace ab0d29a492dcd330 ]---
Kernel panic - not syncing: Fatal exception
Pid: 1250, comm: r Tainted: G D ---------------
2.6.32-356.el6.i686 #1
Call Trace:
[<c08476df>] ? panic+0x6e/0x122
[<c084b63c>] ? oops_end+0xbc/0xd0
[<c084b260>] ? do_general_protection+0x0/0x210
[<c084a9b7>] ? error_code+0x73/
-------------
Petr says: "
I've analysed the bug and I think that xen_iret() cannot cope with
mangled DS, in this case zeroed out (null selector/descriptor) by either
xen_failsafe_callback() or RESTORE_REGS because the corresponding LDT
entry was invalidated by the reproducer. "
Jan took a look at the preliminary patch and came up a fix that solves
this problem:
"This code gets called after all registers other than those handled by
IRET got already restored, hence a null selector in %ds or a non-null
one that got loaded from a code or read-only data descriptor would
cause a kernel mode fault (with the potential of crashing the kernel
as a whole, if panic_on_oops is set)."
The way to fix this is to realize that the we can only relay on the
registers that IRET restores. The two that are guaranteed are the
%cs and %ss as they are always fixed GDT selectors. Also they are
inaccessible from user mode - so they cannot be altered. This is
the approach taken in this patch.
Another alternative option suggested by Jan would be to relay on
the subtle realization that using the %ebp or %esp relative references uses
the %ss segment. In which case we could switch from using %eax to %ebp and
would not need the %ss over-rides. That would also require one extra
instruction to compensate for the one place where the register is used
as scaled index. However Andrew pointed out that is too subtle and if
further work was to be done in this code-path it could escape folks attention
and lead to accidents.
Reviewed-by: Petr Matousek <pmatouse@redhat.com>
Reported-by: Petr Matousek <pmatouse@redhat.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0ee364eb316348ddf3e0dfcd986f5f13f528f821 upstream.
A user reported the following oops when a backup process reads
/proc/kcore:
BUG: unable to handle kernel paging request at ffffbb00ff33b000
IP: [<ffffffff8103157e>] kern_addr_valid+0xbe/0x110
[...]
Call Trace:
[<ffffffff811b8aaa>] read_kcore+0x17a/0x370
[<ffffffff811ad847>] proc_reg_read+0x77/0xc0
[<ffffffff81151687>] vfs_read+0xc7/0x130
[<ffffffff811517f3>] sys_read+0x53/0xa0
[<ffffffff81449692>] system_call_fastpath+0x16/0x1b
Investigation determined that the bug triggered when reading
system RAM at the 4G mark. On this system, that was the first
address using 1G pages for the virt->phys direct mapping so the
PUD is pointing to a physical address, not a PMD page.
The problem is that the page table walker in kern_addr_valid() is
not checking pud_large() and treats the physical address as if
it was a PMD. If it happens to look like pmd_none then it'll
silently fail, probably returning zeros instead of real data. If
the data happens to look like a present PMD though, it will be
walked resulting in the oops above.
This patch adds the necessary pud_large() check.
Unfortunately the problem was not readily reproducible and now
they are running the backup program without accessing
/proc/kcore so the patch has not been validated but I think it
makes sense.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.coM>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20130211145236.GX21389@suse.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cb214ede7657db458fd0b2a25ea0b28dbf900ebc upstream.
When a HP ProLiant DL980 G7 Server boots a regular kernel,
there will be intermittent lost interrupts which could
result in a hang or (in extreme cases) data loss.
The reason is that this system only supports x2apic physical
mode, while the kernel boots with a logical-cluster default
setting.
This bug can be worked around by specifying the "x2apic_phys" or
"nox2apic" boot option, but we want to handle this system
without requiring manual workarounds.
The BIOS sets ACPI_FADT_APIC_PHYSICAL in FADT table.
As all apicids are smaller than 255, BIOS need to pass the
control to the OS with xapic mode, according to x2apic-spec,
chapter 2.9.
Current code handle x2apic when BIOS pass with xapic mode
enabled:
When user specifies x2apic_phys, or FADT indicates PHYSICAL:
1. During madt oem check, apic driver is set with xapic logical
or xapic phys driver at first.
2. enable_IR_x2apic() will enable x2apic_mode.
3. if user specifies x2apic_phys on the boot line, x2apic_phys_probe()
will install the correct x2apic phys driver and use x2apic phys mode.
Otherwise it will skip the driver will let x2apic_cluster_probe to
take over to install x2apic cluster driver (wrong one) even though FADT
indicates PHYSICAL, because x2apic_phys_probe does not check
FADT PHYSICAL.
Add checking x2apic_fadt_phys in x2apic_phys_probe() to fix the
problem.
Signed-off-by: Stoney Wang <song-bo.wang@hp.com>
[ updated the changelog and simplified the code ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1360263182-16226-1-git-send-email-yinghai@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e575a86fdc50d013bf3ad3aa81d9100e8e6cc60d upstream.
Without this patch, it is trivial to determine kernel page
mappings by examining the error code reported to dmesg[1].
Instead, declare the entire kernel memory space as a violation
of a present page.
Additionally, since show_unhandled_signals is enabled by
default, switch branch hinting to the more realistic
expectation, and unobfuscate the setting of the PF_PROT bit to
improve readability.
[1] http://vulnfactory.org/blog/2013/02/06/a-linux-memory-trick/
Reported-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Suggested-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20130207174413.GA12485@www.outflux.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d911e03d097bdc01363df5d81c43f69432eb785c upstream.
Since ed4f209 "s390/time: fix sched_clock() overflow" a new helper function
is used to avoid overflows when converting TOD format values to nanosecond
values.
The kvm interrupt code formerly however only worked by accident because of
an overflow. It tried to program a timer that would expire in more than ~29
years. Because of the old TOD-to-nanoseconds overflow bug the real expiry
value however was much smaller, but now it isn't anymore.
This however triggers yet another bug in the function that programs the clock
comparator s390_next_ktime(): if the absolute "expires" value is after 2042
this will result in an overflow and the programmed value is lower than the
current TOD value which immediatly triggers a clock comparator (= timer)
interrupt.
Since the timer isn't expired it will be programmed immediately again and so
on... the result is a dead system.
To fix this simply program the maximum possible value if an overflow is
detected.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
commit 93040ae5cc8dcc893eca4a4366dc8415af278edf upstream.
Fixed spelling error in a comment as pointed out by DaveM.
Also refactored existing code a bit to provide placeholders for another ASIC
Bug workaround that will be checked-in soon after this.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit daf3ec688e057f6060fb9bb0819feac7a8bbf45c ]
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9c13cb8bb477a83b9a3c9e5a5478a4e21294a760 ]
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6caab7b0544e83e6c160b5e80f5a4a7dd69545c7 ]
If lower layer driver leaves the ip header in the skb fragment, it needs to
be first pulled into skb->data before inspecting ip header length or ip version
number.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6731d2095bd4aef18027c72ef845ab1087c3ba63 ]
There are transients during normal FRTO procedure during which
the packets_in_flight can go to zero between write_queue state
updates and firing the resulting segments out. As FRTO processing
occurs during that window the check must be more precise to
not match "spuriously" :-). More specificly, e.g., when
packets_in_flight is zero but FLAG_DATA_ACKED is true the problematic
branch that set cwnd into zero would not be taken and new segments
might be sent out later.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
