============================================================================= MOXA Smartio Family Device Driver Ver 1.1 Installation Guide for Linux Kernel 2.2.x and 2.0.3x Copyright (C) 1999, Moxa Technologies Co, Ltd. ============================================================================= Content 1. Introduction 2. System Requirement 3. Installation 4. Utilities 5. Setserial 6. Troubleshooting ----------------------------------------------------------------------------- 1. Introduction The Smartio family Linux driver, Ver. 1.1, supports following multiport boards. -C104P/H/HS, C104H/PCI, C104HS/PCI, CI-104J 4 port multiport board. -C168P/H/HS, C168H/PCI 8 port multiport board. This driver has been modified a little and cleaned up from the Moxa contributed driver code and merged into Linux 2.2.14pre. In particular official major/minor numbers have been assigned which are different to those the original Moxa supplied driver used. This driver and installation procedure have been developed upon Linux Kernel 2.2.5 and backward compatible to 2.0.3x. This driver supports Intel x86 and Alpha hardware platform. In order to maintain compatibility, this version has also been properly tested with RedHat, OpenLinux, TurboLinux and S.u.S.E Linux. However, if compatibility problem occurs, please contact Moxa at support@moxa.com.tw. In addition to device driver, useful utilities are also provided in this version. They are - msdiag Diagnostic program for detecting installed Moxa Smartio boards. - msmon Monitor program to observe data count and line status signals. - msterm A simple terminal program which is useful in testing serial ports. - io-irq.exe Configuration program to setup ISA boards. Please note that this program can only be executed under DOS. All the drivers and utilities are published in form of source code under GNU General Public License in this version. Please refer to GNU General Public License announcement in each source code file for more detail. In Moxa's ftp sites, you may always find latest driver at ftp://ftp.moxa.com or ftp://ftp.moxa.com.tw. This version of driver can be installed as Loadable Module (Module driver) or built-in into kernel (Static driver). You may refer to following installation procedure for suitable one. Before you install the driver, please refer to hardware installation procedure in the User's Manual. We assume the user should be familiar with following documents. - Serial-HOWTO - Kernel-HOWTO ----------------------------------------------------------------------------- 2. System Requirement - Hardware platform: Intel x86 or Alpha machine - Kernel version: 2.0.3x or 2.2.x - gcc version 2.72 or later - Maximum 4 boards can be installed in combination ----------------------------------------------------------------------------- 3. Installation 3.1 Hardware installation There are two types of buses, ISA and PCI, for Smartio family multiport board. ISA board --------- You'll have to configure CAP address, I/O address, Interrupt Vector as well as IRQ before installing this driver. Please refer to hardware installation procedure in User's Manual before proceed any further. Please make sure the JP1 is open after the ISA board is set properly. PCI board --------- You may need to adjust IRQ usage in BIOS to avoid from IRQ conflict with other ISA devices. Please refer to hardware installation procedure in User's Manual in advance. IRQ Sharing ----------- Each port within the same multiport board shares the same IRQ. Up to 4 Moxa Smartio Family multiport boards can be installed together on one system and they can share the same IRQ. 3.2 Driver files and device naming convention The driver file may be obtained from ftp, CD-ROM or floppy disk. The first step, anyway, is to copy driver file "mxser.tgz" into specified directory. e.g. /moxa. The execute commands as below. # cd /moxa # tar xvf /dev/fd0 or # cd /moxa # cp /mnt/cdrom//mxser.tgz . # tar xvfz mxser.tgz You may find all the driver and utilities files in /moxa/mxser. Following installation procedure depends on the model you'd like to run the driver. If you prefer module driver, please refer to 3.3. If static driver is required, please refer to 3.4. Dialin and callout port ----------------------- This driver remains traditional serial device properties. There're two special file name for each serial port. One is dial-in port which is named "ttyMxx". For callout port, the naming convention is "cumxx". Device naming when more than 2 boards installed ----------------------------------------------- Naming convention for each Smartio multiport board is pre-defined as below. Board Num. Dial-in Port Callout port 1st board ttyM0 - ttyM7 cum0 - cum7 2nd board ttyM8 - ttyM15 cum8 - cum15 3rd board ttyM16 - ttyM23 cum16 - cum23 4th board ttyM24 - ttym31 cum24 - cum31 Board sequence -------------- This driver will activate ISA boards according to the parameter set in the driver. After all specified ISA board activated, PCI board will be installed in the system automatically driven. Therefore the board number is sorted by the CAP address of ISA boards. For PCI boards, their sequence will be after ISA boards and C168H/PCI has higher priority than C104H/PCI boards. 3.3 Module driver configuration Module driver is easiest way to install. If you prefer static driver installation, please skip this paragraph. 1. Find "Makefile" in /moxa/mxser, then run # make install The driver files "mxser.o" and utilities will be properly compiled and copied to system directories respectively.Then run # insmod mxser to activate the modular driver. You may run "lsmod" to check if "mxser.o" is activated. 2. Create special files by executing "msmknod". # cd /moxa/mxser/driver # ./msmknod Default major numbers for dial-in device and callout device are 174, 175. Msmknod will delete any special files occupying the same device naming. 3. Up to now, you may manually execute "insmod mxser" to activate this driver and run "rmmod mxser" to remove it. However, it's better to have a boot time configuration to eliminate manual operation. Boot time configuration can be achieved by rc file. Run following command for setting rc files. # cd /moxa/mxser/driver # cp ./rc.mxser /etc/rc.d # cd /etc/rc.d You may have to modify part of the content in rc.mxser to specify parameters for ISA board. Please refer to rc.mxser for more detail. Find "rc.serial". If "rc.serial" doesn't exist, create it by vi. Add "rc.mxser" in last line. Next, open rc.local by vi and append following content. if [ -f /etc/rc.d/rc.serial ]; then sh /etc/rc.d/rc.serial fi 4. Reboot and check if mxser.o activated by "lsmod" command. 5. If you'd like to drive Smartio ISA boards in the system, you'll have to add parameter to specify CAP address of given board while activating "mxser.o". The format for parameters are as follows. insmod mxser ioaddr=0x???,0x???,0x???,0x??? | | | | | | | +- 4th ISA board | | +------ 3rd ISA board | +------------ 2nd ISA board +------------------- 1st ISA board 3.4 Static driver configuration 1. Create link # cd /usr/src/linux/drivers/char # ln -s /moxa/mxser/driver/mxser.c mxser.c 2. Add CAP address list for ISA boards In module mode, the CAP address for ISA board is given by parameter. In static driver configuration, you'll have to assign it within driver's source code. If you will not install any ISA boards, you may skip to next portion. The instructions to modify driver source code are as below. a. # cd /moxa/mxser/driver # vi mxser.c b. Find the array mxserBoardCAP[] as below. static int mxserBoardCAP[] = {0x00, 0x00, 0x00, 0x00}; c. Change the address within this array using vi. For example, to driver 2 ISA boards with CAP address 0x280 and 0x180 as 1st and 2nd board. Just to change the source code as follows. static int mxserBoardCAP[] = {0x280, 0x180, 0x00, 0x00}; 3. Modify tty_io.c # cd /usr/src/linux/drivers/char/ # vi tty_io.c Find pty_init(), insert "mxser_init()" as pty_init(); mxser_init(); 4. Modify tty.h # cd /usr/src/linux/include/linux # vi tty.h Find extern int tty_init(void), insert "mxser_init()" as extern int tty_init(void); extern int mxser_init(void); 5. Modify Makefile # cd /usr/src/linux/drivers/char # vi Makefile Find L_OBJS := tty_io.o ...... random.o, add "mxser.o" at last of this line as L_OBJS := tty_io.o ....... mxser.o 6. Rebuild kernel The following are for Linux kernel rebuilding,for your reference only. For appropriate details, please refer to the Linux document. If 'lilo' utility is installed, please use 'make zlilo' to rebuild kernel. If 'lilo' is not installed, please follow the following steps. a. cd /usr/src/linux b. make clean /* take a few minutes */ c. make bzImage /* take probably 10-20 minutes */ d. Backup original boot kernel. /* optional step */ e. cp /usr/src/linux/arch/i386/boot/bzImage /boot/vmlinuz f. Please make sure the boot kernel (vmlinuz) is in the correct position. If you use 'lilo' utility, you should check /etc/lilo.conf 'image' item specified the path which is the 'vmlinuz' path, or you will load wrong (or old) boot kernel image (vmlinuz). g. chmod 400 /vmlinuz h. lilo i. rdev -R /vmlinuz 1 j. sync Note that if the result of "make zImage" is ERROR, then you have to go back to Linux configuration Setup. Type "make config" in directory /usr/src/linux or "setup". Since system include file, /usr/src/linux/include/linux/interrupt.h, is modified each time the MOXA driver is installed, kernel rebuilding is inevitable. And it takes about 10 to 20 minutes depends on the machine. 7. Make utility # cd /moxa/mxser/utility # make install 8. Make special file # cd /moxa/mxser/driver # ./msmknod 9. Reboot 3.5 Custom configuration Although this driver already provides you default configuration, you still can change the device name and major number.The instruction to change these parameters are shown as below. Change Device name ------------------ If you'd like to use other device names instead of default naming convention, all you have to do is to modify the internal code within the shell script "msmknod". First, you have to open "msmknod" by vi. Locate each line contains "ttyM" and "cum" and change them to the device name you desired. "msmknod" creates the device names you need next time executed. Change Major number ------------------- If major number 30 and 35 had been occupied, you may have to select 2 free major numbers for this driver. There are 3 steps to change major numbers. 1. Find free major numbers In /proc/devices, you may find all the major numbers occupied in the system. Please select 2 major numbers that are available. e.g. 40, 45. 2. Create special files Run /moxa/mxser/driver/msmknod to create special files with specified major numbers. 3. Modify driver with new major number Run vi to open /moxa/mxser/driver/mxser.c. Locate the line contains "MXSERMAJOR". Change the content as below. #define MXSERMAJOR 40 #define MXSERCUMAJOR 45 4. Run # make install in /moxa/mxser/driver. 3.6 Verify driver installation You may refer to /var/log/messages to check the latest status log reported by this driver whenever it's activated. ----------------------------------------------------------------------------- 4. Utilities There are 3 utilities contained in this driver. They are msdiag, msmon and msterm. These 3 utilities are released in form of source code. They should be compiled into executable file and copied into /usr/bin. msdiag - Diagnostic -------------------- This utility provides the function to detect what Moxa Smartio multiport board exists in the system. msmon - Port Monitoring ----------------------- This utility gives the user a quick view about all the MOXA ports' activities. One can easily learn each port's total received/transmitted (Rx/Tx) character count since the time when the monitoring is started. Rx/Tx throughputs per second are also reported in interval basis (e.g. the last 5 seconds) and in average basis (since the time the monitoring is started). You can reset all ports' count by key. <+> <-> (plus/minus) keys to change the displaying time interval. Press on the port, that cursor stay, to view the port's communication parameters, signal status, and input/output queue. msterm - Terminal Emulation --------------------------- This utility provides data sending and receiving ability of all tty ports, especially for MOXA ports. It is quite useful for testing simple application, for example, sending AT command to a modem connected to the port or used as a terminal for login purpose. Note that this is only a dumb terminal emulation without handling full screen operation. ----------------------------------------------------------------------------- 5. Setserial Supported Setserial parameters are listed as below. uart set UART type(16450-->disable FIFO, 16550A-->enable FIFO) close_delay set the amount of time(in 1/100 of a second) that DTR should be kept low while being closed. closing_wait set the amount of time(in 1/100 of a second) that the serial port should wait for data to be drained while being closed, before the receiver is disable. spd_hi Use 57.6kb when the application requests 38.4kb. spd_vhi Use 115.2kb when the application requests 38.4kb. spd_normal Use 38.4kb when the application requests 38.4kb. ----------------------------------------------------------------------------- 6. Troubleshooting The boot time error messages and solutions are stated as clearly as possible. If all the possible solutions fail, please contact our technical support team to get more help. Error msg: More than 4 Moxa Smartio family boards found. Fifth board and after are ignored. Solution: To avoid this problem, please unplug fifth and after board, because Moxa driver supports up to 4 boards. Error msg: Request_irq fail, IRQ(?) may be conflict with another device. Solution: Other PCI or ISA devices occupy the assigned IRQ. If you are not sure which device causes the situation,please check /proc/interrupts to find free IRQ and simply change another free IRQ for Moxa board. Error msg: Board #: C1xx Series(CAP=xxx) interrupt number invalid. Solution: Each port within the same multiport board shares the same IRQ. Please set one IRQ (IRQ doesn't equal to zero) for one Moxa board. Error msg: No interrupt vector be set for Moxa ISA board(CAP=xxx). Solution: Moxa ISA board needs an interrupt vector.Please refer to user's manual "Hardware Installation" chapter to set interrupt vector. Error msg: Couldn't install MOXA Smartio family driver! Solution: Load Moxa driver fail, the major number may conflict with other devices. Please refer to previous section 3.5 to change a free major number for Moxa driver. Error msg: Couldn't install MOXA Smartio family callout driver! Solution: Load Moxa callout driver fail, the callout device major number may conflict with other devices. Please refer to previous section 3.5 to change a free callout device major number for Moxa driver. -----------------------------------------------------------------------------