diff options
Diffstat (limited to 'arch/cris/kernel/setup.c')
| -rw-r--r-- | arch/cris/kernel/setup.c | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/arch/cris/kernel/setup.c b/arch/cris/kernel/setup.c new file mode 100644 index 00000000000..6ec2671078b --- /dev/null +++ b/arch/cris/kernel/setup.c @@ -0,0 +1,193 @@ +/* + * + * linux/arch/cris/kernel/setup.c + * + * Copyright (C) 1995 Linus Torvalds + * Copyright (c) 2001 Axis Communications AB + */ + +/* + * This file handles the architecture-dependent parts of initialization + */ + +#include <linux/config.h> +#include <linux/init.h> +#include <linux/mm.h> +#include <linux/bootmem.h> +#include <asm/pgtable.h> +#include <linux/seq_file.h> +#include <linux/tty.h> + +#include <asm/setup.h> + +/* + * Setup options + */ +struct drive_info_struct { char dummy[32]; } drive_info; +struct screen_info screen_info; + +extern int root_mountflags; +extern char _etext, _edata, _end; + +static char command_line[COMMAND_LINE_SIZE] = { 0, }; + +extern const unsigned long text_start, edata; /* set by the linker script */ +extern unsigned long dram_start, dram_end; + +extern unsigned long romfs_start, romfs_length, romfs_in_flash; /* from head.S */ + +extern void show_etrax_copyright(void); /* arch-vX/kernel/setup.c */ + +/* This mainly sets up the memory area, and can be really confusing. + * + * The physical DRAM is virtually mapped into dram_start to dram_end + * (usually c0000000 to c0000000 + DRAM size). The physical address is + * given by the macro __pa(). + * + * In this DRAM, the kernel code and data is loaded, in the beginning. + * It really starts at c0004000 to make room for some special pages - + * the start address is text_start. The kernel data ends at _end. After + * this the ROM filesystem is appended (if there is any). + * + * Between this address and dram_end, we have RAM pages usable to the + * boot code and the system. + * + */ + +void __init +setup_arch(char **cmdline_p) +{ + extern void init_etrax_debug(void); + unsigned long bootmap_size; + unsigned long start_pfn, max_pfn; + unsigned long memory_start; + + /* register an initial console printing routine for printk's */ + + init_etrax_debug(); + + /* we should really poll for DRAM size! */ + + high_memory = &dram_end; + + if(romfs_in_flash || !romfs_length) { + /* if we have the romfs in flash, or if there is no rom filesystem, + * our free area starts directly after the BSS + */ + memory_start = (unsigned long) &_end; + } else { + /* otherwise the free area starts after the ROM filesystem */ + printk("ROM fs in RAM, size %lu bytes\n", romfs_length); + memory_start = romfs_start + romfs_length; + } + + /* process 1's initial memory region is the kernel code/data */ + + init_mm.start_code = (unsigned long) &text_start; + init_mm.end_code = (unsigned long) &_etext; + init_mm.end_data = (unsigned long) &_edata; + init_mm.brk = (unsigned long) &_end; + +#define PFN_UP(x) (((x) + PAGE_SIZE-1) >> PAGE_SHIFT) +#define PFN_DOWN(x) ((x) >> PAGE_SHIFT) +#define PFN_PHYS(x) ((x) << PAGE_SHIFT) + + /* min_low_pfn points to the start of DRAM, start_pfn points + * to the first DRAM pages after the kernel, and max_low_pfn + * to the end of DRAM. + */ + + /* + * partially used pages are not usable - thus + * we are rounding upwards: + */ + + start_pfn = PFN_UP(memory_start); /* usually c0000000 + kernel + romfs */ + max_pfn = PFN_DOWN((unsigned long)high_memory); /* usually c0000000 + dram size */ + + /* + * Initialize the boot-time allocator (start, end) + * + * We give it access to all our DRAM, but we could as well just have + * given it a small slice. No point in doing that though, unless we + * have non-contiguous memory and want the boot-stuff to be in, say, + * the smallest area. + * + * It will put a bitmap of the allocated pages in the beginning + * of the range we give it, but it won't mark the bitmaps pages + * as reserved. We have to do that ourselves below. + * + * We need to use init_bootmem_node instead of init_bootmem + * because our map starts at a quite high address (min_low_pfn). + */ + + max_low_pfn = max_pfn; + min_low_pfn = PAGE_OFFSET >> PAGE_SHIFT; + + bootmap_size = init_bootmem_node(NODE_DATA(0), start_pfn, + min_low_pfn, + max_low_pfn); + + /* And free all memory not belonging to the kernel (addr, size) */ + + free_bootmem(PFN_PHYS(start_pfn), PFN_PHYS(max_pfn - start_pfn)); + + /* + * Reserve the bootmem bitmap itself as well. We do this in two + * steps (first step was init_bootmem()) because this catches + * the (very unlikely) case of us accidentally initializing the + * bootmem allocator with an invalid RAM area. + * + * Arguments are start, size + */ + + reserve_bootmem(PFN_PHYS(start_pfn), bootmap_size); + + /* paging_init() sets up the MMU and marks all pages as reserved */ + + paging_init(); + + /* We don't use a command line yet, so just re-initialize it without + saving anything that might be there. */ + + *cmdline_p = command_line; + +#ifdef CONFIG_ETRAX_CMDLINE + strlcpy(command_line, CONFIG_ETRAX_CMDLINE, COMMAND_LINE_SIZE); + command_line[COMMAND_LINE_SIZE - 1] = '\0'; + + /* Save command line for future references. */ + memcpy(saved_command_line, command_line, COMMAND_LINE_SIZE); + saved_command_line[COMMAND_LINE_SIZE - 1] = '\0'; +#endif + + /* give credit for the CRIS port */ + show_etrax_copyright(); +} + +static void *c_start(struct seq_file *m, loff_t *pos) +{ + /* We only got one CPU... */ + return *pos < 1 ? (void *)1 : NULL; +} + +static void *c_next(struct seq_file *m, void *v, loff_t *pos) +{ + ++*pos; + return NULL; +} + +static void c_stop(struct seq_file *m, void *v) +{ +} + +extern int show_cpuinfo(struct seq_file *m, void *v); + +struct seq_operations cpuinfo_op = { + .start = c_start, + .next = c_next, + .stop = c_stop, + .show = show_cpuinfo, +}; + + |